Milwaukee V28 0724-20 Manual Del Operador página 6

Taladro de percusión de 13 mm (1/2'')
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Starting, Stopping and Controlling
Speed
1.
To start the tool, grasp the handle fi rmly
and pull the trigger.
2.
To vary the speed, increase or decrease
the pressure on the trigger. The further
the trigger is pulled, the greater the
speed.
3.
To stop the tool, release the trigger.
Make sure the bit comes to a complete
stop before laying the tool down.
Electric Brake
The electric brake engages when the trigger
is released, causing the bit to stop and allow-
ing you to proceed with your work. Generally,
the bit stops within two seconds. However,
there may be a delay between the time
you release the trigger and when the brake
engages. Occasionally the brake may miss
completely. If the brake misses frequently,
the tool needs servicing by an authorized
MILWAUKEE service facility.
Drilling
Set both the hammer/drill and torque selector
collars to the drill positions.
Place the bit on the work surface and ap-
ply fi rm pressure before starting. Too much
pressure will slow the bit and reduce drilling
effi ciency. Too little pressure will cause the
bit to slide over the work area and dull the
point of the bit.
If the tool begins to stall, reduce pressure
slightly to allow the bit to regain speed. If
the bit binds, reverse the motor to free the
bit from the workpiece.
Cold Weather Operation
The V28 Lithium-Ion battery pack can be
used in temperatures down to -4°F. When
the battery pack is very cold, it may pulse for
the fi rst minute of use to warm itself up. Put
the battery pack on a tool and use the tool in
a light application. After about a minute, the
pack will have warmed itself up and operate
normally.
APPLICATIONS
WARNING
To reduce the risk of electric shock,
check work area for hidden pipes
and wires before drilling or driving
screws.
Drilling in Wood, Composition Materials
and Plastic
When drilling in wood, composition materials
and plastic, start the drill slowly, gradually
increasing speed as you drill. When drilling
into wood, use wood augers or twist drill bits.
Always use sharp bits. When using twist drill
bits, pull the bit out of the hole frequently to
clear chips from the bit fl utes. To reduce the
chance of splintering, back work with a piece
of scrap wood. Select low speeds for plastics
with a low melting point.
Drilling in Metal
When drilling in metal, use high speed steel
twist drills or hole saws. Use a center punch
to start the hole. Lubricate drill bits with cut-
ting oil when drilling in iron or steel. Use a
coolant when drilling in nonferrous metals
such as copper, brass or aluminum. Back
the material to prevent binding and distortion
on breakthrough.
10
Drilling in Masonry
When drilling in masonry, select the
ham-
mer-drill operating mode. Use high speed
carbide-tipped bits. Drilling soft masonry
materials such as cinder block requires
little pressure. Hard materials like concrete
require more pressure. A smooth, even fl ow
of dust indicates the proper drilling rate. Do
not let the bit spin in the hole without cutting.
Do not use water to settle dust or to cool bit.
Both actions will damage the carbide.
Driving Screws and Nut Running
Drill a pilot hole when driving screws into
thick or hard materials. Set the torque se-
lector collar to the proper position and set
the speed to low. Use the proper style and
size screwdriver bit for the type of screw
you are using.
With the screwdriver bit in the screw, place
the tip of the screw on the workpiece and
apply fi rm pressure before pulling the trig-
ger. Screws can be removed by reversing
the motor.
Overloading
Continuous overloading may cause perma-
nent damage to tool or battery pack.
WARNING
High rotational force. To reduce the
risk of injury, always hold or brace
securely. Always use side handle
on tools.
Bit Binding
A high rotational force occurs when a bit
binds. If the bit binds, the tool will be forced
in the opposite direction of the bit rotation.
Bits may bind if they are misaligned or when
they are breaking through a hole. Wood
boring bits can also bind if they run into
nails or knots. Be prepared for bit binding
situations.
To reduce the chance of bit binding:
• Use sharp bits. Sharp bits are less likely
to bind when drilling.
• Use the proper bit for the job. There are bits
that are designed for specifi c purposes.
• Use caution when drilling pitchy, knotty,
wet or warped material or when drilling in
material that may contain nails.
Typical Bracing Methods
Forward
Fig. 12
rotation
Reaction
Bracing against the fl oor
Fig. 13
Forward
rotation
Reaction
Bracing against
your leg
Fig. 14
Bracing against a stud
Reaction
Reaction
Forward rotation
Reverse rotation
11

Publicidad

Tabla de contenido
loading

Tabla de contenido