Bosch Professional GSR 14,4 V-EC FC2 Manual Original página 12

OBJ_BUCH-2041-002.book Page 12 Monday, January 12, 2015 10:35 AM
12 | English
Symbol Meaning
Audible engagement (multiple)
* Value dependent of the battery pack
being used
L Sound power level
wA
L Sound pressure level
pA
K Uncertainty
a Vibration total value
h
T Permitted ambient temperature during
1
charging
T Permitted ambient temperature during
2
**
operation and storage
(** Limited performance at temperatures
<0 °C)
Recommended batteries
Recommended chargers
Delivery Scope
Cordless drill/driver, keyless chuck (GFA FC2).
The battery, application tool and other accessories shown or
described are not part of the standard delivery scope.
A complete overview of accessories can be found in our ac-
cessories program.
Intended Use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal and plastic.
The power tool can be used with an angle drill head
(GWA FC2) (accessory), off-set angle adapter (GEA FC2)
(accessory) or keyless chuck (GFA FC2) (delivery scope).
Angle drill head (GWA FC2), off-set angle adapter (GEA FC2)
and keyless chuck (GFA FC2) may be used only with the cord-
less drill/drivers GSR 14,4 V-EC FC2 and GSR 18 V-EC FC2.
Note:
A torque must be pre-selected when driving or tightening met-
ric screws using the angle drill head (GWA FC2). Otherwise
there is a risk of gearbox damage.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.
Technical Data
The technical data of the machine are listed in the table on
page 203.
1 609 92A 14Z | (12.1.15)
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2004/108/EC, 2006/42/EC
including their amendments and complies with the following
standards: EN 60745-1, EN 60745-2-1, EN 60745-2-2.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 12.01.2015
Noise/Vibration Information
The measured values of the machine are listed in the table on
page 203.
Sound emission values determined according to
EN 60745-2-1.
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools