Use As Directed - SLV Elektronik TURNO GU10 Instrucciones De Servicio

SLV Elektronik GmbH
ENGLISH
INSTRUCTION MANUAL FOR
RECESSED CEILING FITTING
TURNO GU10
1. NOTES ON SAFETY
Installation, mounting or works on the electrical connection may
only be carried out by an approved electrician.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no
decoration.
Keep children away from the product.
Operate the product only when it functions properly:
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
2.

USE AS DIRECTED

This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
only be operated when firmly mounted.
only be used in dry condition,
not in damp or dirt-endangered rooms.
not in areas of high air humidity.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
3. OPERATION
Exchange the light source always before it reaches its lifespan, to avoid
personal injuries, or damages of the fixture or other objects.
Disconnect the product from the power supply, before you exchange
the bulbs. Let the light source cool down before replacement.
There exists danger of burning!
Use only light sources that are approved for the product. Approved light
sources are indicated on the type label.
Other types of light sources may cause fire risk, damage the product
or lead to malfunction.
Replacing the light source: Remove the used bulb. Use a piece of
fabric to insert the bulbs. Do not touch them with bare fingers.
Carefully remove any fingerprints from the bulbs. Insert the bulb with
a quarter-turn to the right.
4. MAINTANANCE AND CARE
Disconnect the product from the power supply and let it cool down,
before you clean the product.
If disregarded there may be danger of electric shock or by burning
when cleaning the product.
Cleaning: Clean the product on a regular basis using a slightly
moistened, soft and fluff-free cloth.
5. ADDITIONAL IMPORTANT NOTES
Storage: The product must be stored in a dry and clean environment. Do
not strain the product mechanically during storage.
Warranty: In case of a warranty contact your dealer.
Disposal: Notes on the correct disposal in Germany are found on
www.slv.de.
6. INSTALLATION (only by an approved electrician)
Switch off the mains or respectively the connection lead before doing
any works.
There exists mortal danger from an electric shock.
Use only parts, which are supplied with the product or are described as
accessories!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
The housing maybe voltage-carrying. Danger of electric shock!
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
When using fastening material that is not suitable there may be
danger from falling objects.
Unpacking
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
The product is intended for installation in suspended ceilings.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
Note the minimum distances in the ceiling. Minimum distance to each
side: 5 cm.
Do not cover the product, especially not with insulating
materials.
The light exit should be placed at least so far from the illuminated
surface, as indicated as minimum distance on the type plate of the
luminaire: . Pay special caution to easily inflammable objects
(e.g. curtains).
Separate Installation Steps
Mark and cut the opening (see Technical Data). Do not damage the
mains lead.
Remove the cover on top of the connection clamp.
Loosen the strain relief. Direct the mains lead through the strain relief.
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
For electric connection attach the black or brown wire (live conductor)
of the mains lead with the clamp L and the blue wire (neutral
conductor) of the mains lead with the clamp N. The green-yellow wire
(protective conductor) of the mains lead has to be tightly screwed into
the earth clamp of the product.
Put the cover back on the clamp.
Secure the mains lead with the strain relief.
Direct the downlight into the opening, with the retaining springs pointing
upwards.
Inserting the light source: Use a piece of fabric to insert the bulbs. Do
not touch them with bare fingers. Carefully remove any fingerprints
from the bulbs. Insert the bulb with a quarter-turn to the right.
Check if the product functions properly and is securely fixed.
The product is now ready for operation.
art.-no. 116101/02/03/07
10/2009 © SLV Elektronik GmbH, Daimlerstr. 21-23, 52531 Übach-
Palenberg, Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.