Publicidad
Idiomas disponibles
Idiomas disponibles
3. SETUP-UTILITY
3.1 Menu Structure
Via the setup menu it is possible to adapt basic system settings to your individual needs. To access the setup menu, make sure the device is turned
off. Press and hold Shift -D30- and the Back Button -E34- and turn on the device. The Effect Display will read MASTER. By turning the Navigation
encoder -E31- you can access the various menu items. When you have found your desired menu item, press the encoder. Now you can adjust the
menu item by turning the encoder. Via the Back Button you can return to the previous setup.
3.2 Menu Items
MASTER OUTPUT
Select between stereo and mono.
If your sound system only disposes of mono mode, it is recommended to activate mono, to make sure that the same signal is sent to all speakers.
MASTER LIMITER
The limiter reduces the output signal.
Select between a reduction of 0dB, -3dB, -6dB -12dB.
In order not to exceed a certain volume level, it is helpful to limit the maximum output beforehand.
FADER SETTINGS
Here you can adjust the cut-In settings for crossfader and channel faders in a range of 0.0mm and 3.2mm in 0.1mm steps.
FX FADER CONTROL
Selects whether the Effect Level/Depth slider -A03- controls effect slot 1 only or effect slots 1-3 simultaneously.
USB OUT SETTINGS
It is possible to to send different input signals from the mixer via the USB Port to your computer.
USB
PHONO Control Tone
CD Control Tone
CF A
CF B
OUT 1+2
MIC
Aux
Post Fader Deck 1
None
PHONO Control Tone
CD Control Tone
CF A
CF B
OUT 3+4
MIC
Aux
Post Fader Deck 2
None
REC OUT
CF A
CF B
MIC
OUT 5+6
Aux
Post Fader Deck 1
Post Fader Deck 2
None
FILTER RESO
The filter's response curve can be adjusted. In order to increase the response, simply increase the percentage value.
TLKOVR L (Talkover Level)
Determines how much the signal will be suppressed by the mic signal. -6dB, -12dB, -18dB, -24dB
ISO XOVR (Isolator Crossover)
Adapt the EQ's bass and high crossover frequencies to your requirements.
SHIFT LOCK
If active, the Shift Button needs to be toggled instead of being held to switch to the shift layer.
VELOCITY SENS
If active, Pads -D24- are velocity sensitive.
PAD SENS (Pad sensitivity)
Selects the sensitivity of the Performance Pads -D24- in four steps. "ULTRA" means very low pressure is needed while in "LOW" Pads need to be
pressed with higher pressure.
MIC BTH (Mic Booth)
ON: The mic signal is also sent via the booth output.
OFF: The mic signal is not sent via the booth output. If the case may be, the OFF setting can prevent feedback.
MIC LOW CUT
When turned on, low frequencies (f<80Hz) will be cut off.
AUX GAIN COMPENSATION
You can increase the Aux Input's input level in order to achieve louder playback of sources with a weaker signal (e.g. smartphones).
LED CHECK
All LEDs will be activated in order to check their functionality.
FACTORY RESET
If you have adjusted a setting that cannot be reversed, you can select this item to bring all settings back to default.
18
Sub Value
Type
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
SW
CC
MIDI (hex)
Channel
Control
Vakue
MIDI Out
N
32
0
N
32
1
N
32
2
N
32
3
N
32
4
N
32
5
N
32
6
N
32
7
N
32
0
N
32
1
N
32
2
N
32
3
N
32
4
N
32
5
N
32
6
N
32
7
R
7F
0
R
7F
1
R
7F
2
R
7F
3
R
7F
4
R
7F
5
R
7F
6
R
7F
7
Pick-up
Request
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Publicidad
Capítulos
