On/Off Switch - BLACK&DECKER PRO Serie Manual De Instrucciones

ENGLISH
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified
person in order to avoid damage or injury. If the power
cord is replaced by an equally qualified person, but
not authorized by Black & Decker, the warranty will
not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Read Instructions Manual
Use Eye Protection
Use Ear Protection
V ........... Volts
A ........... Amperes
Hz ......... Hertz
W........... Watts
min........ minutes
ADDITIONAL SAFETY INSTRUCTIONS
FOR ANGLE GRINDERS
Always use eye and ear protection when operating this tool.
Personal protective equipment such as dust mask, gloves,
helmet and apron should be worn.
Do not cut or grind light metal with a magnesium content
exceeding 80%, since this type of metal is flammable.
Only use grinding and cutting discs and other accessories
recommended in this manual.
Make sure that the maximum speed of the grinding or
cutting disc exceeds the no-load speed of the tool.
........ Alternating Current
........ Direct Current
n .......... No-Load Speed
0
........ Class II Construction
........ Earthing Terminal
........ Safety Alert Symbol
.../min.... Revolutions or
Reciprocation
per minute
Do not use grinding and cutting discs that do not conform
to the dimensions stated in the technical data. Do not use
separate reducing bushings or adapters or make
unauthorised modifications to adapt large hole abrasive
wheels.
Do not cut workpieces requiring a maximum depth of cut
exceeding that of the cutting disc.
Do not use cutting discs for side grinding.
Inspect grinding and cutting discs before each use. Do not
use chipped, cracked or otherwise defective discs.
Ensure that the abrasive product is correctly mounted and
tightened before use and run the tool at no-load for 30 s
in a safe position, stop immediately if there is considerable
vibration or if other defects are detected. If this condition
occurs, check the machine to determine the cause.
Ensure that blotters are used when they are provided with
the bonded abrasive product and when they are required.
When applying a threaded hole disc, ensure that the thread
is long enough to accept the spindle length.
Never use the tool without the guard.
Check that the workpiece is properly supported.
Do not exert side pressure on the grinding or cutting disc.
Ensure that sparks resulting from use do not create a hazard
e.g. do not hit persons, or ignite flammable substances.
Beware that after switching off the tool the wheel continues
to rotate for a short period.
Ensure that ventilation slots are kept clear when working
in dusty conditions. If it should become necessary to clear
dust, first disconnect the tool from the mains supply. Avoid
damaging internal parts, use a soft brush or dry cloth, do
not use metallic objects.
Abrasive wheels shall be stored and handled with care in
accordance with manufacturer's instructions and always
store grinding and cutting discs in a dry place.
FEATURES
This tool includes some or all of the following features.

1. On/off switch

2. Lock-off button
3. Side handle
4. Spindle lock
5. Guard
ASSEMBLY
Warning! Make sure that the tool is switched off and
unplugged.
Fitting and removing the guard (fig. A)
Fitting
Place the tool on a table, with the spindle (6) facing up.
Hold the guard (5) over the tool as shown.
Align the holes in the adjusting plate (7) with the screw holes (8).
Press the guard down and insert the screws (9) into the holes.
Tighten the screws.
14