Vitamix Venturist Serie Manual Del Usuario página 5

To Avoid Possible Burns, Never Start on Speeds Above 1 when Processing Hot Liquids in a Large Container.
Escaping steam, splashes or contents may burn. Always start on Variable 1, then slowly increase to 10.
DO NOT use your 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl to heat ingredients or to blend hot liquids. Heated
ingredients and liquids may create internal pressure which could cause the cup to burst and cause injury.
DO NOT continuously use your machine for more than 75 seconds for the 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl.
If a cup becomes warm to the touch or steams or vents, immediately stop blending ingredients and turn off or
unplug blender. Allow the cup and ingredients to cool to room temperature before removing the blade base.
Parts will become hot with extended use.
DO NOT touch the drive socket in the blender base or the drive spline in the blade base.
To avoid damage or personal injury, DO NOT use the cups (including the blade base or lids) in the microwave.
1. The On/Off switch is on the right hand side of the blender base. Press the On/Off switch to the On (I) position.
2. Load your container according to your recipe or the load order in the illustration here. Note: Recipe ingredients for cups load in the opposite
order of the large containers. DO NOT blend hot liquids in the 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl.
IMPORTANT! Always use the lid and the lid plug on the Large Container when the machine is in operation.
Never operate the blender without checking to make sure that the lid and lid plug are securely locked in place.
3.
Perform one of the following:
• Large Containers - Put the lid onto the container. Push the lid down into place until
the two tabs snap onto the lip of the container. Insert the lid plug. Turn the lid plug
clockwise to lock.
• 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl
base. The seal should fit snugly and evenly around the thread. Thread the blade base
onto the cup in a clockwise direction. DO NOT overtighten or leaking can occur.
4.
Put the container (or cup and blade base) onto the blender base. 0:00 will display
when a container/cup is detected and the blender is ready to operate.
5.
Perform one of the following:
• To use variable speed:
a. Turn the variable speed dial to Variable Speed 1.
b. Press Start/Stop. The blades will begin to turn and the timer will count the
minutes and seconds that the blend has been processing. To set a blend time,
use the +/- icons on the controls.
c. Rotate the Variable Speed Dial between 1 and 10 during the blending cycle to
increase or decrease the speed of the blades.
d. At the end of the blend, rotate the Variable Speed Dial counter-clockwise to
Variable 1. Press Start/Stop.
• To use Programs:
Note: The soup program is not available for use with the cups. DO NOT blend hot liquid
in the 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl . _0_ will be visible on the display when
a program is not available.
a. Rotate the Variable Speed Dial counter-clockwise to the desired program. (The program
time will display on the control panel).
b. Press Start/Stop to start the program. (The blender will automatically stop at the end of
the program.) Press Start/Stop at any time to stop the program.
6. If the mixture stops circulating:
• Large Containers - Insert the tamper through the lid plug and stir until it 'burps'. If this
does not work, press the On/Off switch to stop the motor. Remove the container from
the blender base and use a rubber spatula to press the air bubble away from the blades.
Add liquid if necessary. Replace the lid and lid plug. Return the container to the blender base
and continue blending.
• 20 oz. (0.6 L) cup or 8 oz. (240 ml) bowl
Wait until the blades stop rotating. Remove the cup and blade base from the
blender base. Turn the cup over. Unthread the blade base from the cup. Stir the
ingredients. Add liquid if necessary. Reattach the blade base, place on blender base
and continue blending.
7. After blending, wait until the blades completely stop before removing the lid or
container/cup from the blender base.
8.
If necessary, use the Blade Scraper to remove salsa, jelly, jam, peanut butter, and other
thick ingredients from under the blades only after the blender has been turned off and
the container has been removed from the motor base.
b
l e n d i n g
WARNING
- Put a seal on the bottom thread of the blade
- Press the On/Off switch to stop the motor.
Loading Large Containers
Ice & Frozen
Ingredients
Fruits & Veggies
Leafy Greens
Dry Goods
Liquids
Loading the 20 oz. (0.6 L) cup
Liquids
DO NOT blend hot liquids!
Dry Goods
Leafy Greens
Fruits & Veggies
Ice & Frozen
Ingredients
Before putting the blade
base onto the bowl or cup,
locate the two arrows on
the blade base. Tighten the
blade base onto the bowl or
cup until the arrows line up
within the range marked on
the bowl or cup.
5