Before Use; Installation Work - Pioneer PDP-S02-LR Manual De Instrucciones

English
Thank you for buying this Pioneer product.
Please read through this operating instructions before using
your speaker system so you will know how to make the
most of its performance. After you have finished reading
the operating instructions, store it in a safe place. You will
then know where it is, should you wish to refer to it if
something is unclear while the speaker system is being used.
CAUTION
This product is designed exclusively for use with a
Pioneer 50 inch plasma display.

BEFORE USE

INSTALLATION WORK

The installation of this speaker system must be
carried out by professionals with the adequate skill
and experience. Therefore, when installation or
attaching is to be carried out, be sure to commission
construction specialists or your dealer.
PIONEER will not take any responsibility for
accidents or damage caused by improper assembly
or installation, insufficient strength, incorrect usage,
or natural disasters.
The nominal impedance of this speaker system is 8 ohms.
Connect the speaker system to a stereo amplifier with a
load impedance ranging from 4 to 16 ohms (a model with
"4-16 Ω" displayed on the speaker output terminals).
In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
Do not supply power to the speaker system in
excess of the maximum permissible input.
When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
Do not force a low-powered amplifier to produce
a loud volume of sound (the amplifier's harmonic
distortion will be increased, and you may damage
the speaker).
Please handle the speakers with sufficient care, as
the grille net and th cabinet can become damaged
or broken when they are subjected to strong external
impacts.
To protect the speaker from excessive input power and
abnormal signals, an automatic-reset type protective
device is installed.
When excessive input is sent to the speaker, the
protective device is activated, and the sounds cease to
be produced. When this occurs, reduce the amplifier
volume; the protective device will reset itself in about
5–10 seconds.
CAUTIONS WHEN ASSEMBLING
MOUNTING FITTINGS
Only use the enclosed mounting
fittings for the 50 inch display to attach
the speaker.
The mounting fittings for the 50 inch
display have a tag to distinguish them
from those for the 40 inch display. (See
the illustration.) After checking
carefully ,please attach the fittings.
4
Installation on PDP-501MX, PDP-
V501X, etc.
There are two installation methods.Please follow the
following procedure.
[1] For installation at the side of the
Flat countersunk head
screw
1. Remove the (lower two) hole rivets at the rear of the
2. Install the accessory mounting fitting on the speaker.
3. Confirm the left and the right speaker by the markings
4. Adjust the position so that the gap between the speaker
Distinguishing tag
(Blue)
display
The illustration shows installation on the right side of the
display.
｢PDP-S02」
ＵＰ
Cushion
Mounting fitting
Hexagon screw
display.
(The hole rivets can be removed by turning with a coin or
similar.)
(Take care that the cushion is not peeled off.)
"LEFT" and "RIGHT" on the rear of the speaker, make
sure that the cushion is on the inner side and that the
marking "UP " points up, and then install the speaker
on the display, starting with the lower mounting fitting.
(Fasten only provisionally, as there is play.)
and the display is uniform, and then tighten the screws
firmly.
When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
When the display is to be moved after speaker
installation, do not hold the display by the speakers. Hold
the bottom of the display to move it.
Plasma display
Hole rivet
Washer (ø 15)