Sander Specific Warnings; Placing Tool In Service - Ingersoll Rand 319 Manual De Instrucciones

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
WARNING
Always wear eye protection
when operating or perform-
ing maintenance on this tool.
WARNING
Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable po-
sitions may be harmful to your
hands and arms. Stop using
any tool if discomfort, tingling
feeling or pain occurs. Seek
medical advice before resum-
ing use.
WARNING
Keep body stance balanced
and firm. Do not overreach
when operating this tool.
These Sanders will operate at the free speed
•
specified on the nameplate if the air supply line
furnishes 90 psig (6.2 bar/620 kPa) air pressure at
the tool. Operation at higher air pressure will
result in excessive speed.
Use only a sanding pad, buffing wheel or polishing
•
bonnet with these tools. Do not use any grinding
wheel, bur or metal removing accessory with these
tools. Never use an accessory having a maximum
operating speed less than the free speed of the
Sander in which it is being used.
LUBRICATION
Ingersoll- - Rand No. 50
Always use an air line lubricator with this Sander.
We recommend the following Ingersoll- - Rand
Filter- - Lubricator- - Regulator Unit:
For International - - C28- - C4- - FKG0
For USA - - C28- - 04- - FKG0- - 28
After each two hours of operation, if an air line
lubricator is not used, inject 0.5 to 1 cc of Ingersoll- - Rand
No. 50 Oil into (39). Periodically, remove (33) and
lubricate the gearing with 30 cc of Ingersoll- - Rand No. 67
Grease.
Model Type of
Handle
319, 319- - EU lever
Tested in accordance with ANSI S5.1- - 1971 sanding on steel workpiece
H
♦ Tested in accordance with ISO8662- - 1 sanding on steel workpiece
ISO3744
•
WARNING SYMBOL IDENTIFICATION
90 psig
(6.2bar/620kPa)

SANDER SPECIFIC WARNINGS

PLACING TOOL IN SERVICE

Ingersoll- - Rand No. 67
SPECIFICATIONS
Spindle Free
Thread Speed
5/8"- - 11 5,000
WARNING
Always wear hearing
protection when operating
this tool.
WARNING
Do not carry the tool by the
hose.
WARNING
Operate at 90 psig (6.2 bar/
620 kPa) Maximum air pres-
sure.
When using a pad having a shank, insert the shank
•
to full depth in the collet. When using a pad on a
threaded arbor, make certain the flange nut is
tightened securely. Check the tightness of the collet
nut or flange nut before operating a Sander to
make certain it will not loosen during operation.
MAIN LINES 3 TIMES
AIR TOOL INLET SIZE
TO
AIR
SYSTEM
TO
AIR
TOOL
LUBRICATOR
REGULATOR
BRANCH LINE 2 TIMES
AIR TOOL INLET SIZE
DRAIN REGULARLY
Pad Size
Pressure
7" diameter
2
WARNING
Always turn off the air sup-
ply and disconnect the air
supply hose before install-
ing, removing or adjusting
any accessory on this tool,
or before performing any
maintenance on this tool.
WARNING
Do not use damaged, frayed
or deteriorated air hoses
and fittings.
International Warning Label:
Order Part No. ___________
FILTER
COMPRESSOR
(Dwg. TPD905- -1)
HSound Level
♦Vibrations
dB (A)
•Power
90.8 103.8
Level
2
m/s
1.2