Mounting Precautions - Sharp PN-L601B Manual De Instalación

• This product is for use indoors.
• Since the monitor is heavy, consult your dealer before installing,
removing or moving the monitor.
• When installing, removing or moving the monitor, ensure that this
is carried out by at least 2 people.
• A mounting bracket compliant with VESA specifications is required.
Do not use any screw holes other than VESA holes for installation.
• To attach a VESA-compliant mounting bracket, use M6 screws that
are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness
of the mounting bracket.
• When moving the monitor, be sure to hold it with either both handles
or the 4 corners on the bottom of the unit. Do not place your hand
on the screen. This may cause product damage, failure, or injury.
• Install the monitor with the surface perpendicular to a level surface.
• Mounting the monitor on the wall requires special expertise and
the work must be performed by an authorized SHARP dealer. You
should never attempt to perform any of this work yourself. Our
company will bear no responsibility for accidents or injuries caused
by improper mounting or mishandling.
• This monitor should be used at an ambient temperature between
41°F (5°C) and 95°F (35°C). Provide enough space around the
monitor to prevent heat from accumulating inside.
For the monitor in horizontal orientation
2
[5]
For the monitor in vertical orientation
2
[5]
• If it is difficult to provide sufficient space for any reason such as
the installation of the monitor inside a housing, or if the ambient
temperature may be outside of the range of 41°F (5°C) to 95°F
(35°C), install a fan or take other measures to keep the ambient
temperature within the required range.
• Temperature condition may change when using the display
together with the optional equipments recommended by SHARP. In
such cases, please check the temperature condition specified by
the optional equipments.
• Adhere to the following when installing the monitor in its vertical
orientation. Failing to adhere to the following may cause
malfunctions.
- I nstall the monitor such that the power LED is located on the
bottom side.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See Operation manual.)
- B e sure to clamp the power cord (supplied) onto the cable
clamp attachment below using the supplied cable clamp. When
clamping the power cord, take care not to stress the terminal of
the power cord. Do not bend the power cord excessively.
Cable clamp attachment
4
E

MOUNTING PRECAUTIONS

Unit: inch [cm]
7-7/8 [20]
1-7/16 [3.5]
2
[5]
2 [5]
Unit: inch [cm]
7-7/8 [20]
1-13/16 [4.5]
2
[5]
2 [5]
Power cord (Supplied)
Cable clamp
• Do not block any ventilation openings. If the temperature inside the
monitor rises, this could lead to a malfunction.
• After mounting, please carefully ensure the monitor is secure, and
not able to come loose from the wall or mount.
• Do not place the monitor on a device which generates heat.
• Use the supplied vertical sticker when you install the monitor in
vertical orientation.
Operation panel
Do not remove the factory-affixed sticker but affix the logo sticker
over it. Be careful not to cover the remote control sensor or buttons.
• Be sure to use a wall-mount bracket designed or designated for
mounting the monitor.
• This monitor is designed to be installed on a concrete wall or pillar.
Reinforced work might be necessary for some materials such as
plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can
endure at least 4 times or more the weight of the monitor. Install by
the most suitable method for the material and the structure.
• Do not use the product in locations where the unit is exposed to
direct sunlight or other strong light. Since this product operates
with infrared rays, such light may cause a malfunction.
■
Connecting the USB cable
Warning:
• Contact your dealer or a service engineer to have the USB
cable installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
• Before connecting the USB cable, turn off the main power switch
and disconnect the power cable from the outlet.
• Use only the supplied USB cable.
■
Installing the power switch
Warning:
• Contact your dealer or a service engineer to have the power
switch installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
1. Remove the screw (x1) from the monitor.
2. Remove the protective seal and connect the power switch
connector, making sure the connector is in the correct orientation.
3. A lign the clamps with the slot in the bottom of the unit and tighten
the screws (x2).
Make sure that the clamps are firmly secured.
Take care that the cable is not caught or pinched.
4. Replace the screw that was removed in 1.
Protective seal
Connector
Power switch
Mounting
bracket
Logo
Bottom
Mounting
bracket