Troubleshooting - Truper COMP-60LB Manual De Usuario

TROUBLESHOOTING

WARNING! FOR YOUR OWN SAFETY ALWAYS TURN OFF AND DISCONNECT THE UNIT BEFORE TRYING TO SOLVE ANY
PROBLEM.
PROBLEM
Oil pumping 1. Blocked admission filter
2. Oil viscosity is to low.
3. Oil level is too high (when excessive fill-up is
4. Piston rings are broken or not settled. Gaps not
5. Cylinders or pistons with scratches, worn or
Banging and rattling. 1. Loose pulley or excessive axial backlash in the
2. Coal in the upper side of the piston.
3. Leaky, broken, carbonized or loose valves or
4.Worn or scratched rod bearings
5. Defective bearing in the crank or in the motor shaft.
6. Cylinders or pistons with scratches, worn or with
7. Transmission band has too much play.
Air feed is reduced. 1. Admission filter is clogged.
2. Air leaks in piping (in the machine or in the external
3. Leaky, broken, carbonized or loose valves or
4. Worn or scratched rod bearings
5. Defective bearing in the crank or in the motor shaft.
6. Transmission band has too much play.
Motor overload is 1. Oil viscosity is too high.
triggered or consumes 2. Probable false contact in the motor terminals or
excessive current
3. Tension drop in the feeding line.
4. Deficient energy regulation (unbalanced line).
5. Leaky, broken, carbonized or loose valves or
6. Defective bearing in the crank or in the motor shaft.
7. Cylinders or pistons with scratches, worn or with
8. Transmission band is too tight
9. Faults in the check valve.
Oxidation in the 1. Wrong type of oil is being used.
cylinders 2. The compressor has been operating in a damp
Excessive starting and 1. Draining the tank is necessary.
stopping 2. Air leaks in pipeline (in the machine or the external
3. Leaks in the tank security valve
The compressor runs 1. There is a possibility the flywheel is blocked.
excessively hot 2. Leaks in the tank safety valve.
3. The oil level is too low.
4. Leaky, broken, carbonized or loose valves or
5. Wrong rotation direction.
6
CAUSE
possible).
tiered or stuck in the slot.
streaked.
motor shaft.
restricted air ducts.
Loose motor fan.
lines.
system).
restricted air ducts.
Loose motor fan.
their connections.
restricted air ducts.
Loose motor fan.
lines.
place for a long period of time.
system).
restricted air ducts.
* TASC: Truper® Authorized Service Center.
SOLUTIONS
1. Clean filter or replace if necessary.
2. Change and use the right oil.
3. Remove excessive oil from the casing.
4. Go to your nearest TASC*
5. Go to your nearest TASC*
1 - 7. For service and repairs go to your nearest
TASC*
1. Clean filter or replace if necessary.
2. Look for air leaks. Use sealing tape in all the leaky
connections.
3 - 6. For service and repairs go to your nearest
TASC*
1. Change and use the right type of oil.
2. Go to the nearest TASC*
3. Check voltage in the feeding line fuses or correct the
motor overload.
4. Consult a qualified electrician.
5 - 9. For service and repairs go to your nearest
TASC*
1. Change and use the right type of oil
2. For service and repairs go to your nearest TASC*
1. Open the valve set in the lower side of the tank and
drain.
2. Inspect to detect air leaks. Use sealing tape in all
leaky connections.
3. Inspect to detect leaks. If changing the valve is
necessary go to a TASC*
1. Go to the nearest TASC*
2. Inspect to detect leaks. If the valve needs replacing
go to the nearest TASC*
3. Add oil in the casing up to the right level.
4. Go to the nearest TASC*
5. Go to the nearest TASC*