Bosch GWS 180-LI Professional Manual Original página 21

Ocultar thumbs Ver también para GWS 180-LI Professional:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 36
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (5) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(6) is pressed unintentionally. As long as the battery is inser-
ted in the power tool, it is held in position by means of a
spring.
To remove the battery (5), press the release button (6) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator  or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Bosch Power Tools
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Fitting Protective Equipment
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
to
clicks into place.
Adjust the position of the protective guard (8) to meet the
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (8) into
the required position.
Always position the protective guard (8) such that all
u
three cams on the unlocking lever (1) engage in the
corresponding openings on the protective guard (8).
Adjust the protective guard (8) such that sparking in
u
Capacity
the direction of the operator is prevented.
60−100 %
The protective guard (8) must only be adjustable
u
30−60 %
while the unlocking lever (1) is actuated. Otherwise,
5−30 %
the power tool must not be used any more under any
0−5 %
English | 21
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
Place the protective guard
(8) onto the holder on the
power tool until the coding
cams of the protective
guard are aligned with the
holder. When doing so,
press and hold the unlock-
ing lever (1).
Press the protective guard
(8) onto the spindle collar
until the shoulder of the
protective guard is sitting
on the flange of the power
tool and rotate the protect-
ive guard until it audibly
1 609 92A 5GT | (27.03.2020)

Publicidad

Tabla de contenido
loading

Tabla de contenido