Before Starting The Equipment - EINHELL TC-DH 43 Manual De Instrucciones Original

L sound pressure level ..................... 96.5 dB(A)
pA
K uncertainty ........................................ 0.55 dB
pA
L sound power level ..................... 102.9 dB(A)
WA
K uncertainty ........................................ 0.55 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
Anl_TC_DH_43_SPK9.indb 15 Anl_TC_DH_43_SPK9.indb 15
= 16.29 m/s
2
h
2
- 15 -
GB
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
5.1 Additional handle (Fig. 2)
For safety reasons you must only use the
demolition hammer with the additional
handle. The additional handle (3) enables you to
achieve better stability whilst using the demolition
hammer. The additional handle (3) can be turned
into any required position. Undo the screw (a) by
turning it in the "+" direction. Now turn the additio-
nal handle (3) into the most comfortable working
position for yourself and then tighten the screw (a)
again by turning it in the "-" direction.
5.2 Inserting the tool (Fig. 3-4)
•
Clean the tool before fitting it and apply a thin
coating of grease to the tool shaft.
•
Pull out the locking bolt (4) as far as possible,
turn it through 180° and release it.
•
Insert the tool into the tool mounting (5) and
push it in as far as possible. (see Fig. 3)
•
Pull out the locking bolt (4) again, turn it
through 180° in the opposite direction and
release it.
•
Check the lock by pulling the tool.
5.3 Removing the tool
To remove the tool, proceed in reverse order.
6. Operation
Important.
To avoid danger, the machine must only be
held using the two handles (1/3). Otherwise
you may suff er an electric shock if you chisel into
cables.
19.09.2018 09:47:16 19.09.2018 09:47:16