Proper Use - EINHELL TC-SM 2531/2 U Manual De Instrucciones Original

Ocultar thumbs Ver también para TC-SM 2531/2 U:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

33. Lever
34. Movable stop rail
35. Laser
36. Locking screw for stop rail
37. ON/OFF switch for laser
38. Transport handle
39. Laser battery case
40. Battery compartment cover
41. Screw
42. Cover plate
a
round-head screw
b
spring washer
c
washer, small
d
nut
e
hex screw
f
washer, large
g
spring washer
h
nut
100 Complete supporting frame
101 Top cross strut
102 Top longitudinal strut
103 Bottom cross strut
104 Bottom longitudinal strut
105 Leg
106 Rubber foot
107 Locking screw
2.2 Items supplied
Please check that the article is complete as
specified in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
Drag, crosscut and miter saw
Clamping device
Anl_TC_SM_2531_2_U_SPK8.indb 42
Anl_TC_SM_2531_2_U_SPK8.indb 42
GB
2 x workpiece support
Sawdust bag
Hexagon key
Round-head screw (24x)
Spring washer (24x)
Washer, small (24x)
Nut (24x)
Hex screw (4x)
Washer, large (8x)
Nut, large (4x)
Spring washer (4x)
Table width extensions (2x)
Locking screw (2x)
Original operating instructions

3. Proper use

The drag, crosscut and miter saw is designed
for cross-cutting wood and wood-type materials
which are appropriate for the machine's size. The
saw is not designed for cutting firewood.
The equipment is to be used only for its pre-
scribed purpose. Any other use is deemed to be
a case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suit-
able saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also impera-
tive to observe the accident prevention regula-
tions in force in your area. The same applies for
the general rules of health and safety at work.
The manufacturer will not be liable for any
changes made to the equipment nor for any
damage resulting from such changes. Even when
the equipment is used as prescribed it is still
- 42 -
30.06.2021 08:18:59
30.06.2021 08:18:59

Publicidad

Tabla de contenido
loading

Tabla de contenido