Skil 7461 Manual Original página 9

! before the sanding surface reaches the workpiece,
you should switch on the tool
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it from
the workpiece
• Speed control 9
For optimal sanding results on different materials
- with wheel G 2 you can set the desired sanding speed
- adjust speed to grit size used
- before starting a job, find the optimal speed and grit by
testing out on spare material
• Holding and guiding the tool w
! while working, always hold the tool at the grey-
coloured grip area(s)
- guide the tool parallel to the working surface
- do not apply too much pressure on the tool; let the
sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots H 2 uncovered
• Sanding
- the amount of material removed is determined by the
selection of the sanding sheet, the preselected sanding
speed and the applied pressure
! intensifiying the sanding pressure does not lead
to an increase of the sanding capacity, but to
increased wear of the tool and the sanding sheet
! never use the same sanding sheet for wood and
metal
APPLICATION ADVICE
• For determining the optimal grit (and speed), table q can
be used as reference
! always test out first on a piece of scrap material
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H 2 )
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, please send the
tool undismantled together with proof of purchase to your
dealer.
• Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the warranty conditions please ask your
dealer).
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
Measured in accordance with EN 62841 the sound
•
pressure level of this tool is 83.0 dB(A) and the sound
power level 94.0 dB(A) (uncertainty K = 3 dB), and
the vibration 7.1 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Ponceuse
excentrique
INTRODUCTION
• Cet outil est conçu pour le ponçage à sec du bois,
plastique, métal et mastic et des surfaces peintes
Cet outil n'est pas conçu pour un usage professionnel
•
• Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Support plateau
B Vis du support plateau
C Feuille de ponçage
D Réservoir à poussière
E Adaptateur de l'aspirateur*
F Interrupteur marche/arrêt
G Molette de réglage de la vitesse de ponçage
H Fentes de ventilation
* NON FOURNI EN STANDARD
SECURITE
AVERTISSEMENTS DE SECURITE GENERAUX POUR
L'OUTIL ELECTRIQUE
AVERTISSEMENT Lisez tous les avertissements
-
de sécurité, toutes les instructions, illustrations et
caractéristiques fournies avec cet outil électrique.
Le non-respect du suivi de toutes les instructions reprises
ci-dessous peut provoquer un électrochoc, un incendie et/ou
des blessures graves.
9
7461