Cardin Elettronica PRG Serie Manual Del Usuario página 14

PROGRAMMING PROCEDURE (parameter setting)
• All the functions of the electronic programmer can be set in the Display menu "LCD1" using the three buttons contained therein:
- use the arrows to navigate through the menu and/or to adjust the display contrast;
- use "PROG/OK" to modify the parameter settings and/or to confirm.
PROGRAM
OPTIONS
TB FI TA TD
SAFETY DEVICES
FS CP TC TAL
MOTION
DISPLAY
REMOTE
00.000.007
CC2X24 V1.00
Press an arrow
SEQUENTIAL COM.
key to enter the
OPEN-SHUT/
main menu
OPEN-STOP-SHUT
AUTO. RECLOSING
The number of
ON/OFF
PRE-FLASHING
manoeuvres
ON/OFF
carried out by
the operator
arm and the
SEQUENTIAL COM.
OPEN-SHUT/
ECU model are
OPEN-STOP-SHUT
always shown
AUTO. RECLOSING
on the opening
ON/OFF
PRE-FLASHING
screen of the
ON/OFF
display.
SEQUENTIAL COM.
The plug
OPEN-SHUT/
symbol
OPEN-STOP-SHUT
AUTO. RECLOSING
indicates that the
ON/OFF
ECU is working
PRE-FLASHING
ON/OFF
off mains power.
PRE-FLASHING
The fully
ON/OFF
WARNING LIGHTS
charged battery
FIXED/
INTERMITTENT
symbol
INDICATOR LIGHT
indicates that the
FIXED/
INTERMITTENT
ECU is working
off battery power
at 100%.
WARNING LIGHTS
FIXED/
75%
INTERMITTENT
INDICATOR LIGHT
FIXED/
50%
INTERMITTENT
PHOTOCELL INVERT
25%
DURING CLOSING/
AND IN STOP
0%
INDICATOR LIGHT
FIXED/
INTERMITTENT
"PROG/OK"
PHOTOCELL INVERT
to change
DURING CLOSING/
the value AND IN STOP
TEST FI
Note: 3
ON/OFF
PHOTOCELL INVERT
DURING CLOSING/
AND IN STOP
"PROG/OK"
TEST FI
to change
ON/OFF
the value
TEST FS
Note: 3
ON/OFF
TEST FI
ON/OFF
TEST FS
"PROG/OK"
ON/OFF
to change
the value
GATE DELAY
DURING OPENING
Note: 4
ON/OFF
TEST FS
ON/OFF
GATE DELAY
"PROG/OK"
DURING OPENING
to change
ON/OFF
the value
ELECTRIC LOCK
Note: 5
ON/OFF
GATE DELAY
ON/OFF
"PROG/OK"
ELECTRIC LOCK
to change
ON/OFF
the value
MEMO RADIO
ON/OFF
ELECTRIC LOCK
ON/OFF
"PROG/OK"
REMOTE
to change
ON/OFF
the value
OUTPUT LC/CH2
RADIO CHANNEL/
COURTESY LIGHT
MEMO RADIO
ON/OFF
OUTPUT LC/CH2
COURTESY LIGHT/
RADIO CHANNEL
"PROG/OK"
to return to EXIT
'options'
OPTIONS
SAFETY DEVICES
MOTION
Arrow
DISPLAY
to scroll
REMOTE
"PROG/OK"
to confirm
CONTACT TB
NC/8K2
CONTACT FI
"PROG/OK"
NC/8K2
to change
the value CONTACT FS
NC/8K2
CONTACT TB
NC/8K2
"PROG/OK"
CONTACT FI
to change
NC/8K2
the value
CONTACT FS
NC/8K2
CONTACT TB
NC/8K2
"PROG/OK"
"PROG/OK"
CONTACT FI
to change
NC/8K2
the value
CONTACT FS
NC/8K2
CONTACT FI
NC/8K2
"PROG/OK"
"PROG/OK"
CONTACT FS
to change
NC/8K2
the value
CONTACT CP
Note: 1
NC/8K2
CONTACT FS
NC/8K2
"PROG/OK"
CONTACT CP
to change
NC/8K2
the value
EXIT
Note: 2
"PROG/OK"
to return to
'safety devices'
Notes:
1) The indicator light flashes slowly during opening, rapidly during closing; remains lit when the gate is blocked but not completely closed
and is off when the gate is completely closed.
2) FI Mode:
- FI also active when the gate is blocked: If the photocells are in alarm and the gate is blocked, no movement commands will be accepted
(even opening commands);
- FI active only during closing: In both cases activating the FI safety device during the closing stage will force travel direction inversion.
3) Photocell test (FI/FS)
If you enable the security test you will have to connect both the transmitter and the receiver to the controlled load output
(CTRL 24 Vdc). When the test is enabled one second will pass between receiving a command and carrying it out.
4) Opening direction gate delay
If you enable gate delay the following will occur: during the opening movement gate leaf 1 moves first and then gate leaf 2. In the closing
direction gate leaf 2 moves first then gate leaf 1. If gate delay is disabled both gate leaves move simultaneously.
5) Electric lock
If the electric lock is enabled the ELS output (binding post 8) will be activated before gate leaf 1 moves and will remain active until gate leaf
1 has moved a few centimetres.
6) Select the type of motor
BL3924ERB = articulated (reversible)
BLi924 = inside operator
HL2524ESB = underground motor (HL1824/2524)
OPTIONS
SAFETY DEVICES
MOTION
Arrow Arrow
DISPLAY
to scroll to scroll
REMOTE
"PROG/OK" "PROG/OK"
to confirm to confirm
MOTOR SELECTION
BL824
Note: 6
CURRENT SENSOR
"PROG/OK"
"PROG/OK"
LEVEL 1...5
to change
to change
LIMITED OPENING
the value
the value
SETTING 1...5
MOTOR SELECTION
BL824
"PROG/OK" "PROG/OK"
CURRENT SENSOR
to change
to change
LEVEL 1...5
the value the value
LIMITED OPENING
Note: 7
SETTING 1...4
MOTOR SELECTION
BL824
"PROG/OK"
CURRENT SENSOR
to change
to change
LEVEL 1...5
the value the value
LIMITED OPENING
Note: 8
SELECTION 1...4
CURRENT SENSOR
LEVEL 1...5
"PROG/OK"
LIMITED OPENING
to change to change
SETTING 1...5
the value the value
DIST. FROM CLOSE
Note: 9
STEPS 1...9
LIMITED OPENING
SETTING 1...5
"PROG/OK"
to change
DIST. FROM CLOSE
the value
STEPS 1...9
GATE DELAY
Note: 10
STEPS 0...9
DIST. FROM CLOSE
"PROG/OK"
STEPS 1...9
to change
GATE DELAY
the value
STEPS 0...9
Note: 11
BRAKING ROOM
SETTING 1...3
GATE DELAY
STEPS 0...9 "PROG/OK"
to change
BRAKING ROOM
the value
SETTING 1...3
Note: 12
BRAKING SPEED
SETTING 1...3
BRAKING ROOM
SETTING 1...3
BRAKING SPEED
SETTING 1...3
PAUSE TIME
130 SEC.
BRAKING SPEED
SETTING 1...3
PAUSE TIME
130 SEC.
"PROG/OK"
to return to
EXIT
'motions'
BL824 = articulated
BLi1000 = inside operator
BLTOW24 = articulated
14
OPTIONS
SAFETY DEVICES
MOTION
DISPLAY
REMOTE
"PROG/OK"
to confirm
CONTRAST
0....63
"PROG/OK"
REAR LIGHTING
to confirm
ALWAYS ON/60/30 SEC.
EXIT
CONTRAST
0....63
"PROG/OK"
REAR LIGHTING
to change
ALWAYS ON/60/30 SEC.
the value
EXIT
CONTRAST
0....63
REAR LIGHTING
ALWAYS ON/60/30 SEC.
EXIT
"PROG/OK"
to return to
'display'
* * * * * * * * * * * * * * *
* *
"PROG/OK" * PAUSE TIME *
to confirm
* 180 SEC. *
* *
* * * * * * * * * * * * * * *
Press the arrows to increase or
decrease the value (max. 240 sec).
Keeping the arrows held down will
force the value to scroll rapidly.
BL224E = straight arm BLEGOS = straight arm
BL1924ASW = articulated
BL3924ESB = articulated (self-locking)
* * * * * * * * * * * * * * *
* *
* SET CONTRAST *
SEC.
26
* *
* *
* * * * * * * * * * * * * * *
Press the arrows
to increase or
decrease the value
(max. 63)
(BLEGOS/BLESOL)