Assembly - EINHELL TC-TS 2025/1 U Manual De Instrucciones

6. Assembly

Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Assembling the base frame
(Fig. 4-5)
•
Turn the saw upside down and place it on the
floor.
•
Use the hex screws (a) to fasten the four legs
(29) loosely to the saw.
•
Now use the round-head screws (c) and the
nuts (b) to fasten the longitudinal struts (31)
and the cross-struts (30) loosely to the legs.
Important: The longer struts have to be used
on the sides.
•
Finally, tighten all screws and nuts on the
base frame.
•
Screw the additional legs (36) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 5).
•
Plug the rubber feet (13) onto the legs (29).
6.2 Assembling the table width extension
(Fig. 6)
•
Use the screws (a) and nuts (b) to fasten the
table width extensions (33) loosely to the saw
table (1).
•
Screw the supports (32) loosely onto the saw
housing and onto the table width extensions
(33) (Fig. 6).
•
Align the table width extensions (33) level
with the saw table.
•
Finally, tighten all screws.
6.3 Fitting / removing the saw blade guard
(Fig. 3,7)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Do not tighten the screw (15) too far – the bla-
de guard must be able to move freely.
•
To remove the saw blade guard, proceed in
reverse order.
Warning!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
Anl_TC_TS_2025_1_U_2025_1_ECO_SPK9.indb 26 Anl_TC_TS_2025_1_U_2025_1_ECO_SPK9.indb 26
GB
6.4 Changing the table insert (Figure 8)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the 1 countersunk head screws (17).
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.5 Setting the splitter (Fig. 9,10)
•
Danger! Pull out the power plug.
•
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
•
Remove the saw blade guard (see 6.2).
•
Take out the table insert (6) (see 6.4).
•
Slacken the fixing screw (19).
•
Push up the splitter (5) until the gap between
the saw table (1) and the upper edge of the
splitter (5) equals approx. 10 cm.
•
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
•
Retighten the screw (19) and mount the table
insert (6) (Fig. 8).
6.6 Fitting/replacing the blade (Fig. 7)
•
Important! Pull out the power plug first.
•
Remove the table insert by undoing the two
countersunk head screws (see 6.4).
•
Undo the nut with a size 21 wrench on the
nut itself and a second fork wrench (size 10)
on the motor shaft to apply counter-pressure.
•
Important! Turn the nut in the direction of
rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the bla-
de at an angle.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Mount and fasten the new saw blade in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter (5) and the saw gu-
ard (2) (see 6.3., 6.5.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
- 26 -
13.04.2018 11:41:56 13.04.2018 11:41:56