Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Spring shackle
Rearward
Hitch Shown In Proper Position
Equipment Required: Pull wire (Provided), straps or rope
to support the bumper if needed.
Fastener Kit: 75938F
Wrenches: ¾", 21mm
Drill Bits: None
Teeth side
against hitch
Shackle with
carriage bolt
1 1 1 1
Qty. (2)
Carriage bolt ½-13 X 1.50 GR5
2 2 2 2
Qty. (2)
Spacers
1.
Loosen spare tire for ease of installment.
2.
Feed the coiled end of the pull wire into the bottom of the spring shackle and out the access hole on the inside of the shackle.
Attach the spacer and bolt, onto the pull wire and pull back into location as shown. Both sides.
3.
Loosen and remove existing flange nuts holding the bumper to the frame. 2 each side to be re-used. Support bumper if
necessary.
4.
Raise hitch into position feeding the pull wires through the adjacent holes on the hitch. Sliding the slots in hitch onto the bumper
bolts for support, reattaching the flange nuts.
5.
Using pull wires, pull the fasteners through the hitch side brackets. Feed conical washer over pull wire, using the washer to hold
the bolt in place remove the pull wires and attach the hex nut. Tighten to hold hitch in place, repeat on all fasteners.
6.
Torque all fasteners to specifications below
7.
Re-install the spare tire loosened in Step 1.
Tighten all M14 X 2.0 fasteners with torque wrench to 148 Lb.-Ft. (201 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2014 Cequent Performance Products, Inc
Installation Instructions
Bumper
Frame rail
Spring
shackle
Spare tire
not shown
Pull wire
Ford F-150
.
Requires factory step bumper
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: xxx
1 1 1 1
2 2 2 2
Access holes
3 3 3 3
4 4 4 4
Fasteners typical
both sides
3 3 3 3
Qty. (2)
4 4 4 4
Qty. (2)
Sheet 1 of 3
Printed in Mexico
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
8000 LB (3632 Kg)
6000 LB (2724 Kg)
Spring
shackle
Hitch shown in position
Conical tooth washers ½"
Hex nut ½-13
75938N
8-7-14
Form F206 Rev B 9-17-2012
Part Numbers:
75938
87672
44754
Max Tongue
WT (LB)
800 LB (363 Kg)
900 LB (409 Kg)
D
Accessory Rating
Bumper
attachment
Bumper attachment
flange nuts to be
re-used. 2 each side
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75938
Resumen de contenidos para Cequent Performance Products 75938
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75938N 8-7-14 Rev. A 2014 Cequent Performance Products, Inc Printed in Mexico Form F206 Rev B 9-17-2012...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75938N 8-7-14 Rev. A 2014 Cequent Performance Products, Inc. Imprimé au Mexique Form F206 Rev B 9-17-2012...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2014 Cequent Performance Products, Inc. Hoja 3 de 3 75938N 8-7-14 Rev.