Bosch GWS 8-115 PROFESSIONAL Instrucciones De Servicio página 28

OBJ_BUCH-340-001.book Page 29 Thursday, February 8, 2007 8:55 AM
In this case, interrupt the cutting process and allow the
diamond cutting disc to cool by running the machine for
a short time at maximum speed with no load.
Noticeable decreasing work progress and circular
sparking are indications of a diamond cutting disc that
has become dull. Briefly cutting into abrasive material
(e. g. lime-sand brick) can resharpen the disc again.
Information on Structures
Slots in structural walls are subject to the Standard
DIN 1053 Part 1, or country-specific regulations.
These regulations are to be observed under all cir-
cumstances. Before beginning work, consult the
responsible structural engineer, architect or the con-
struction supervisor.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep
the machine and ventilation slots clean.
In extreme working conditions, conductive
dust can accumulate in the interior of the
machine when working with metal. The pro-
tective insulation of the machine can be
degraded. The use of a stationary extraction
system is recommended in such cases as
well as frequently blowing out the ventila-
tion slots and installing a residual current
device (RCD).
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for
Bosch power tools.
In all correspondence and spare parts order, please
always include the 10-digit article number given on
the type plate of the machine.
WARNING! Important instructions for connect-
ing a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to the
following code:
Do not connect the blue or brown wire to the earth
terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it must be
disposed of safely.
1 609 929 L00 • 8.2.07
Service and Customer Assistance
Exploded views and information on spare parts can be
found under:
www.bosch-pt.com
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service: . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 82
✆ Advice line:. . . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax: . . . . . . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 89
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
✆ Service: . . . . . . . . . . . . . . .+353 (0)1 / 4 66 67 00
Fax: . . . . . . . . . . . . . . . . . . . . .+353 (0)1 / 4 66 68 88
Australia and New Zealand
Robert Bosch Australia Pty. Ltd.
RBAU/SPT
1555 Centre Road
P.O. Box 66
3168 Clayton/Victoria
✆ . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 44
Fax: . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 45
www.bosch.com.au
Disposal
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According the European Guideline
2002/96/EC for Waste Electrical and
Electronic Equipment and its imple-
mentation into national right, power
tools that are no longer usable must be collected sep-
arately and disposed of in an environmentally correct
manner.
Subject to change without notice.
English | 29