Operating Instructions - Multiplex RX-9-DR light M-LINK Instrucciones

! These operating instructions are an integral part
of the product, and contain important information
and safety notes. Please store them in a safe place,
where you can find them at any time, and pass
them on to the new owner if you sell the receiver.
1. S
PECIFICATION
Order No.
Reception system
Servo channel count
Servo frame rate
Signal resolution
Current drain
Aerial length of which feed cable approx. 17 cm and
Operating voltage
Operating
temperature range
Weight
Dimensions
2. S F
PECIAL EATURES
•
High-quality 9-channel receiver assembled using the latest
SMT methods, exploiting MULTIPLEX 2.4 GHz M-LINK
technology, suitable for all types of model.
•
Dual receivers:
Each receiver features two complete reception circuits
working in parallel (receiver diversity).
This ensures excellent reception quality by minimising
directional effects.
•
Supplementary signal pre-amplification:
For highest possible sensitivity.
•
In-line connector arrangement:
Ideal for models with limited internal space.
•
HOLD / FAIL-SAFE function.
•
Integral SET button and LED:
For binding, FAIL-SAFE programming, RESET and
displaying operating status information.
•
Integral PC interface:
Carry out updates using the RX DataManager PC program.
3. S N
AFETY OTES
! Please read the instructions before using the receiver.
! Use the receiver only for the intended applications
( 4.).
! Ensure the power supply is of adequate capacity (
! Observe the installation notes (
! Carry out regular range checks (
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions for the
RX-9-DR light M-LINK 2.4 GHz receiver
RX-9-DR light M-LINK
# 5 5816
2.4 GHz FHSS M-LINK
Frequency Hopping Spread Spectrum
MULTIPLEX-LINK
9
Fast Response: 14 ms
Standard: 21 ms
12-bit, 3872 steps
Approx. 60 mA (excl. servos)
Total: approx. 20 cm (2 x),
active aerial section approx. 3 cm
3.5 V ... 9.0 V
4 - 6 NiCd / NiMH (NiXX) cells
2S LiPo / LiIo
- 20 °C ... + 55 °C
19 g
Approx. 49.0 x 34.0 x 11.5 mm
10.).
11.).
4. A
PPLICATIONS
The RX-9-DR light M-LINK 2.4 GHz receiver is a radio control
receiver intended exclusively for use in model sport. It is pro-
hibitted to employ them for other purposes such as full-size
(people-carrying) vehicles or industrial installations.
5. C
OMPATIBILITY
The RX-9-DR light M-LINK 2.4 GHz receiver can only be
operated in conjunction
MULTIPLEX M-LINK transmission technology.
These are as follows (correct as of June 2010):
•
ROYALpro 7, 9 and 16 M-LINK.
•
ROYALevo or pro 7, 9 and 12 with firmware version V3.xx
and the HFM4 M-LINK 2.4 GHz RF module*.
•
PROFImc 3010, 3030 and 4000 with the HFM3 M-LINK
2.4 GHz RF module*.
•
COCKPIT SX M-LINK.
•
MULTIPLEX transmitters with the HFMx M-LINK 2.4 GHz
RF module.
! *Note:
Unless stated otherwise, when this document refers to the
transmitter types ROYALevo, ROYALpro, and PROFImc 3010,
3030 and 4000, the terms refer to the 2.4 GHz M-LINK versions.
6. P
OWER
The RX-9-DR light M-LINK receiver works within a broad range
of voltages from 3.5 V ... 9.0 V, i.e. it can be used with receiver
batteries consisting of four to six NiXX cells or 2S LiPo / 2S LiIo.
! Note: if you intend to use a five-cell or six-cell NiXX battery,
or a 2S LiPo or 2S LiIo pack, it is essential to check that all the
servos, gyros and other components connected to the system
are approved for use with this higher operating voltage.
! Note: ensure that the power supply is adequate
A power supply system in good condition and of adequate capa-
city for the specific application plays an indispensable role in the
safe operation of any model:
•
Use only high-quality receiver batteries of adequate capacity.
Balance and maintain them carefully, and charge them fully.
•
Ensure that all cables are of adequate conductor cross-
section. Keep all wiring as short as possible, and use the
absolute minimum of plug / socket connections.
•
Use high-quality switch harnesses exclusively.
•
Brief collapses in the power supply voltage (lasting a few
milli-seconds) have no adverse effect on the receiver. Longer
voltage collapses to below 3.5 V may cause a receiver reset,
resulting in a brief interruption in reception. This may be due
to a receiver battery which is almost flat, too weak or de-
fective, cables of inadequate cross-section, poor-quality
connectors or an overloaded or defective BEC system.
7. R
ECEIVER
This receiver employs the UNI connector system, which is
compatible with the connector systems used by most radio
control manufacturers (e.g. HiTEC, robbe/Futaba, Graupner/JR).
The receiver sockets are marked as follows:
6.).
with transmitters
S
UPPLY
C
ONNECTIONS
which utilise
Page 9