Emerson InSinkErator INVOLVE VIEW Serie Manual Del Usuario página 5

3
MOUntIng the tanK
a
Tank must be
mounted level
to ensure
proper operation.
NOTICE
Property Damage: Tank must be located
within 16" of faucet and within 30" or less
of a standard grounded outlet. DO NOT extend
plumbing or electrical lines.
b
leave 1/4" for
hanging tank.
1
Mount tank vertically in an area that
allows clearance on the underside of
the tank for drainage, if necessary.
DO NOT over tighten screws.
4
cOnnectIng faUcet tO tanK
a
(1) (2)
2
2
3
NOTICE
Property Damage: Pinched or blocked water
1
2
lines may cause damage to the dispenser tank.
Check to make sure tubes are connected
properly and are pushed down as far as possible.
3
To see a tutorial of this installation:
http://goo.gl/AZOHu
3
8
select a spot under the sink to mount
tank vertically within reach of both
plumbing and electrical connections.
the tank should be within 16" or less
of faucet water lines and within 30"
or less of a standard grounded outlet.
while holding tank in place on
the spot selected for installation,
use a pencil to mark locations for
2 hanging screws.
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
2
(not supplied) for installation into drywall.
Pre-drill 1/8" pilot holes at marks.
Plastic
turn screws into pre-drilled holes,
leaving 1/4" exposed.
hang the tank on the screws.
tighten the screws with only 1/2
3
turn clockwise.
without depressing the gray button,
place the snap-connect fitting at
(3)
the end of the blue 1/4" tube onto
1
the left fitting on the tank, pushing
until it clicks into place. (1)
slip the flexible white 7/16" tube
over barbed middle fitting and slide
down approximately 1/2". (2)
slip the clear 5/16" tube over the
far right smooth fitting and slide
down approximately 1/2". (3)
Visually check for pinched or
crimped tubes.
Hose clamps are not needed for any
of the connections.
Fiber
Washer Wing Nut
5
fInal wateR cOnnectIOn
a
Brass Nut
Ferrule
Brass Insert
Brass
nut
Plastic
tube
3/8"
Plastic
tube
Property Damage: Join remaining tube
to cold water supply only.
a
Brass Nut
Brass Nut
Ferrule
Brass Nut
Brass Insert Ferrule
Ferrule
Brass Insert
1/4"
copper
tube
tube
Plastic
tube
Property Damage: Join remaining tube
to cold water supply only.
6
Brass Nut
fIll tanK & then cOnnect POweR
Ferrule
Brass Insert
a
Plastic
tube
2
Scalding Hazard: The faucet dispenses
near-boiling (212ºF) water which can
instantly cause scalds or burns. Use care
when operating this appliance.
b
3
Electric Shock Hazard: A standard grounded
outlet within 30" of the dispenser is required
under the sink. Do not use an extension
cord set with the dispenser.
HC-View/HC-Wave
Brass Nut
Ferrule Install a t-fitting (not included) onto the
cold water supply line.
Brass
ferrule
Insert
Install dedicated water control valve with
3/8" compression fitting.
at the end of the white 3/8" tube from
the quick-connector, slide the supplied
brass nut and ferrule over the tube and
then push in the brass tube insert.
NOTICE
Insert the white 3/8" tube into the 3/8"
compression fitting and tighten.
H-View/H -Wave/Contour/Classic
Brass
nut
Install a t-fitting (not included) onto the
ferrule
Brass Nut
cold water supply line.
Ferrule
Install dedicated water control valve with
Plastic
tube
1/4" compression fitting (not included).
at the end of the copper 1/4" tube,
slide the brass nut and ferrule provided
NOTICE with the control valve over the tube.
Insert the copper tube into the 1/4"
compression fitting and tighten.
Brass Nut
Ferrule
turn on the cold water supply.
Depress the dispenser's HOT
NOTICE
handle and hold it until water flows from
the spout (approximately 1 to
2 minutes).
Run the water for at least 2 minutes to
flush lines (both the hot and cold handles
independently if applicable).
check all connections to ensure they are
tight and that there are no leaks.
NOTICE
Plug in instant hot water tank.
Water will be cold at first.
Allow 12-15 minutes for water to reach
target temperature.
Gurgling or hissing is normal during the
initial heating cycle.
Brass Nut
Brass Nut
Ferrule
Ferrule
Brass Insert
9