DeWalt DCE200 Manual De Instrucciones página 5

f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
e ) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g ) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside the
specified range may damage the battery and increase
the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
Additional Safety Rules for Press Tool

WARNING: Use the press tool only with D
or D WALT-approved attachments. Other uses or
e
modifying the press tool for other applications
may damage the press tool, damage the
attachments and/or can result in a faulty
installation. Faulty installations can result in
catastrophic failures, injury to installers and
damage to property.

WARNING: Though this D
reach the proper pressure to complete a press
successfully, connections can only be effective
when the connection is free from defects and
when the press is properly prepared according
to the fitting manufacturer's installation
procedures. Proper preparation and installation
is the responsibility of the installing contractor.
• Only use D
e
with a compression range rated for this tool.
Keep all body parts away from the attachments
•
during operation and any time the power is ON. A
moment of inattention while operating power tools,
may result in serious personal injury. Fingers or hands
can be crushed, fractured or amputated if they become
caught in the attachments.
Inspect tool and attachments before use. Never
•
attempt to repair or use a damaged jaw set or other
attachment. Replace with a new jaw set or attachment.
• This tool produces large forces that can break
attachments or parts and cause injury. Always be
attentive and take proper safety precautions, including
wearing eye protection.
Crush hazard. Never run the tool without a jaw set or
•
attachment installed.
• Only trained personnel should operate this tool.
• Before operating, inspect the tool and LEDs on the
diagnostics panel. Correct any problems before using
the tool. Reference the Troubleshooting Guide or
LED Indications sections for a list of possible problems
and solutions.
• Before operating, inspect job site for hazards
including chemicals or waste that could remain
in pipes.
• Before operating, read and understand all safety
and operating instructions including the fitting
manufacturer's installation instructions and the
instructions for any other equipment used with this
tool. Failure to follow all instructions and warnings
may result in property damage and/or serious
personal injury.
Keep the pressing area of the tool free from hands
•
and other objects while tool is in use. Fingers could
be crushed.
• Secure and support the material prior to making the
press to prevent movement during pressing.
• Keep a firm grip on the tool at all times. Forces on the
tool may change during and after the press.
Press operations may cause material pieces to fly.
•
Flying particles can cause permanent eye damage.
WALT
e
ALWAYS wear eye protection.
WALT press tool will
e
WALT or D WALT-approved attachments
e
3