Safety Notes; Applications; Mounting - IMG STAGELINE PARL-1DMX Manual De Instrucciones

be selected with button FUNCTION
The LED of button MODE lights up continuously.
– Selection of the colour change programmes
Sh 1 – Sh12 with button FUNCTION
The LED of button MODE flashes slowly.
– Selection of the colour transition programmes
Ch 1 – Ch16 and Fade with button FUNCTION
The LED of button MODE flashes quickly.
Note: For control via the remote control no DMX signal must
be present at the DMX INPUT (10).

2 Safety Notes

The unit corresponds to all required directives of the
EU and is therefore marked with
WARNING The unit uses hazardous mains voltage
(230 V~). Leave servicing to skilled per-
sonnel only and do not insert anything
into the air vents; inexpert handling may
result in electric shock.
Please observe the following items in any case:
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
G
Do not operate the unit or immediately disconnect
the mains plug from the mains socket
1. if the unit or the mains cable is visibly damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled per-
sonnel.
G
Never pull the mains cable for disconnecting the
mains plug from the mains socket, always seize the
plug.
G
For cleaning only use a dry, soft cloth, never use
chemicals or water.
G
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not safely mounted or
not correctly operated, or if it is not repaired in an
expert way.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in ac cord -
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
.

3 Applications

This flat LED spotlight serves for illumination e. g. on
stage, in discotheques, and festival rooms. As a light
source, 212 extra bright LEDs are used which have a
low power consumption, a low heat development and
a long life. The LEDs allow to radiate coloured light in
the three primary colours (red, green and blue) and
light which can be mixed from the primary colours by
addition. Besides, colour transitions and stroboscopic
effects are possible.
light controller (4 DMX control channels). However, it
can also be operated on its own or with the remote
control LC-3 available as an accessory or with the con-
trol panel LED-4C from "img Stage Line".

4 Mounting

G
G
WARNING The spotlight must be mounted in a safe
1. Fix the spotlight via the mounting bracket (1), e. g.
2. As an alternative the spotlight can also be set up as
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
The spotlight is designed for the control via a DMX
Always place the unit so that a sufficient air circula-
tion is ensured during operation. The air vents at the
housing must not be covered in any case.
The distance to the radiated object should be 10 cm
as a minimum.
and expert way. If it is installed at a
place where people may walk or sit
under, it must additionally be secured
(e. g. by a safety rope at the mounting
bracket; fix the safety rope so that the
maximum falling distance of the unit
would not exceed 20 cm).
with a stable mounting screw or a support for light-
ing units (C hook) to a cross bar.
To align the spotlight, release the two locking
screws (2) at the mounting bracket. Adjust the desired
inclination of the spotlight and retighten the screws.
desired (fig. 1). The mounting bracket serves as a
support to prevent the spotlight from tilting over. For
this purpose tighten the locking screws (2) very firmly.
, GB
13