Descargar Imprimir esta página

Fein FSC500QSL Serie Instrucciones De Uso página 5

Publicidad

Idiomas disponibles

Idiomas disponibles

OBJ_BUCH-0000000238-004.book Page 5 Wednesday, May 16, 2018 1:44 PM
Wear personal protective equipment. Depend-
ing on application, use face shield, safety
goggles or safety glasses. Where appropriate,
wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping
small abrasive or workpiece fragments. The
safety glasses must be capable of protecting
against flying particles generated by the vari-
ous operations. Prolonged exposure to high
intensity noise may cause loss of hearing.
Do not direct the power tool against yourself,
other persons or animals. Danger of injury
from sharp or hot application tools.
Do not rivet or screw any name-plates or
signs onto the power tool. If the insulation is
damaged, protection against an electric shock
will be ineffective. Adhesive labels are recom-
mended.
Handling hazardous dusts.
When working with power
WARNING
tools, such as when grinding,
sanding, polishing, sawing or for other work
procedures where material is removed, dusts
develop that are both hazardous to one's
health and can spontaneously combust or be
explosive.
Contact with or inhaling some dust types can
trigger allergic reactions to the operator or
bystanders and/or lead to respiratory infec-
tions, cancer, birth defects or other reproduc-
tive harm.
Examples of such materials which contain
chemicals that can produce hazardous dusts,
are:
– Asbestos and materials containing asbes-
tos;
– Lead-containing coatings, some wood
types such as beech and oak;
– Minerals and metal;
– Silicate particles from bricks, concrete and
other materials containing stone;
– Solvent from solvent-containing paint/
varnish;
– Arsenic, chromium and other wood pre-
servatives;
– Materials for pesticide treatment on boat
and ship hulls;
– Stainless steel dust, metal dust and non-
ferrous metal dust;
Clean the ventilation openings on the power
tool at regular intervals using non-metal
tools. The blower of the motor draws dust
into the housing. An excessive accumulation
of metallic dust can cause an electrical hazard.
Before putting into operation, check the
power connection and the power plug for
damage.
Recommendation: The tool should always be
supplied with power via a ground fault circuit
interrupter (GFCI) with a rated current of
30 mA or less.
After working gypsum-containing materials:
Blow out the ventilation openings of the
power tool and the switch element with dry
and oil-free compressed air. Otherwise, gyp-
sum-containing dust can settle in the power
tool housing and switch element, which can
harden in connection with humidity. This can
impair the switching mechanism.
To minimize the unwanted intake of these
materials:
– Use dust extraction matched appropriately
for the developing dust.
– Use personal protective equipment, such
as a P2 filter-class dust protection mask.
– Provide for good ventilation of the work-
place.
The risk from inhaling dusts depends on how
often these materials are worked. Materials
containing asbestos may only be worked on
by specialists.
Wood and light-metal dust can
CAUTION
cause spontaneous combus-
tion or explosions.
Hot mixtures of sanding dust and paint/var-
nish remainders or other chemical materials
in the filter bag or the vac filter can self-ignite
under unfavorable conditions, such as spark-
ing from sanding metal, continuous sunlight
or high ambient temperatures. To prevent
this:
– Avoid overheating the material being
sanded and the power tool.
– Empty the dust collector/container in time.
– Observe the material manufacturer's
working instructions.
– Observe the relevant regulations in your
country for the materials being worked.
en
5

Publicidad

loading

Este manual también es adecuado para:

7 229 46 68 09 0