Important Safety Instructions - Makita AN610H Manual De Instrucciones

ENGLISH
(Original instructions)
1 Compressor air output per
minute
2 Nailing frequency (times/min.)
3 Adjuster
4 Shallow
5 Deep
6 Too deep
7 Flush
8 Too shallow
9 Hook
10 Hole
11 Protrusion
12 Nose adapter
13 Magazine cap
14 Latch lever
SPECIFICATIONS
Model
Air pressure
Nail length
Nail capacity
Min. hose diameter
Dimensions (L x H x W)
Net weight
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2" x 4" housing.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
WHEN USING THIS
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and mainte-
nance of the tool, read this instruction manual before
using the tool.
• Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
6
Explanation of general view
15 Door
16 Adjustfit
17 Change plate
18 Arrow
19 Nail guide
20 Feeder
21 Trigger
22 Contact element
23 Change lever
24 0.7 mm or less thick for steel
plate
25 Thickness of workpiece
26 10 mm or more
27 C-shaped steel
(Thickness 1.6 mm – 2.3 mm)
ENB109-1
TOOL, BASIC SAFETY
28 Nail driven to a proper depth
29 Nail driven too deep will cause
30 Nail length
31 Wood thickness
32 Concrete range 10 – 15 mm
33 Small rod
34 Screwdriver
35 Cap
36 Drain cock
37 Air filter
38 Oiler
39 Pneumatic oil
AN610H
0.98 – 2.26 MPa (9.8 – 22.6 bar)
Wire-collated coil nail 32 mm – 65 mm
Sheet-collated coil nail 32 mm – 65 mm
Wire-collated coil nail 250 pcs, 300 pcs, 400 pcs
Sheet-collated coil nail 200 pcs
5.0 mm
282 mm x 277 mm x 136 mm
1.9 kg
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or rolled
up. No necktie should be worn.
• Rushing the job or forcing the tool is dangerous. Han-
dle the tool carefully. Do not operate when under the
influence of alcohol, drugs or the like.
• General Tool Handling Guidelines:
1. Always assume that the tool contains fasteners.
2. Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
3. Do not activate the tool unless the tool is placed
firmly against the workpiece.
4. Respect the tool as a working implement.
5. No horseplay.
6. Do not hold or carry the tool with a finger on the
trigger.
7. Do not load the tool with fasteners when any one of
the operating controls is activated.
8. Do not operate the tool with any power source other
than that specified in the tool operating/safety
instructions.
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as gas-
oline, thinner, paint, gas, adhesives, etc.; they will ignite
and explode, causing serious injury.
deformation of workpieces