Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

90565382 SSL16 SSL20 NEW Smart Select.qxd:??????-00 BDL500 laser
KEYLESS CHUCK (FIGURE F)
WARNING:
Make certain the lock-off
button is engaged to prevent switch actuation
before installing or removing accessories.
To insert a drill bit or other accessory:
1. Grasp the rear half of the chuck (4) with
one hand and use your other hand to
rotate the front half (4a) in the
counterclockwise direction, as viewed
from the chuck end.
2. Insert the bit or other accessory fully into
the chuck, and tighten securely by holding
the rear half of the chuck and rotating the
front portion in the clockwise direction as
viewed from the chuck end.
WARNING:
Do not attempt to tighten drill bits (or any other accessory) by gripping the
front part of the chuck and turning the tool on. Damage to the chuck and personal injury
may occur when changing accessories.
SCREW DRIVING
For driving fasteners, the reversing button should be pushed to the left. Use reverse
(button pushed to the right) for removing fasteners. When moving from forward to reverse,
or vice versa, always release the trigger switch first.
ON BOARD BIT STORAGE (FIGURE G)
A bit storage slot (8) is built-in to the area just above the battery pack.
DRILLING
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions.
• Use appropriate and required safety equipment, as instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety Instructions.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the
drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting
but not so much as to stall the motor or deflect the bit.
• Hold the drill firmly with two hands to control its twisting action.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT
TO START IT. DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the
last part of the hole.
• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce
jamming.
• Make sure switch turns drill on and off.
F
4a
4
G
8
10
6/3/10
1:40 PM
Page 10
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service personnel, always using identical replacement parts.

TROUBLESHOOTING

Problem
Possible Cause
• Unit will not start.
• Battery pack not installed properly.
• Battery pack not charged.
• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into
• Charger not plugged in.
• Surrounding air temperature
too hot or too cold.
• Unit shuts off abruptly.
• Battery pack has reached its
maximum thermal limit.
• Out of charge. ( To
maximize the life of the
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING:
The use of any accessory not recommended for use with this tool could be
hazardous.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
lithium-ion battery (or battery pack) indicates that the costs to recycle the
battery (or battery pack) at the end of its useful life have already been paid by
Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries in the trash
or municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent lithium-ion
batteries. Help protect our environment and conserve natural resources by returning the
tool to an authorized Black & Decker service center for recycling. You may also contact
your local recycling center for information on where to drop off the spent battery, or call
1-800-8-BATTERY.
Possible Solution
• Check battery pack
installation.
• Check battery pack charging
requirements.
charger until green LED
appears.
• Plug charger into a working
outlet. Refer to "Important
Charging Notes" for more
details.
• Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (4.5°C) or below
105 degrees F (+40.5°C).
• Allow battery pack to cool
down.
• Place on charger and
allow to charge.
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ssl20

Tabla de contenido