Service Information - Black+Decker HD400 Manual De Instrucciones

USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f For drilling in masonry, set the drilling mode selector
(3) to the
position.
f For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
(Only for HD500)
f Slacken the side handle (7) by turning the grip
counterclockwise.
f Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f Tighten the side handle by turning the grip clockwise.
Switching on and off
f To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
(HD500)
f For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f To switch the tool off, release the speed switch. To
switch the tool off when in continuous operation, press
the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.

SERVICE INFORMATION

BLACK+DECKER offers a full network of company-owned
and authorized service locations. All BLACK+DECKER
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service. For more information about our authorized service
centers and if you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest you, or visit us at www.BlackandDecker-
la.com
SPECIFICATIONS HD400
Power 550W
Voltaje
AR, B2C 220V ~ 50Hz
B3 120V ~ 60Hz
B2 220V ~ 60Hz
BR 127V ~ 60Hz
No-load speed 3000/min (rpm) 0 - 2800/min (rpm)
Blows per minute 0 - 45000gpm (bpm)
Max drill capacity
Steel/Concrete 3/8" (10mm)
Wood 25/32" (20mm) 25/32" (20mm)
ENGLISH • 13
HD500.
550W
220V ~ 50Hz
120V ~ 60Hz
220V ~ 60Hz
127V ~ 60Hz
1/2" (13mm)