Manufacturer's Warranty - Palmer PAN16 DI-BOX Manual De Usuario

mono signal and to direct it as balanced mono signal to the PA system. Using the MERGE LINK / IN switch, the
LINK out can be converted to a second input. In this case, stereo outputs of the instrument are connected to
a PAN16 channel via the two jacks (INPUT and LINK / IN) and the switch is pressed down. The mono summed
looped signal is present on the rear panel LINK socket.
paD Switch
The PAN16 can also be used to feed speaker signals into a mixer. To do this, connect the amplifier output with
the "Input" socket and loop the signal to the speakers via the "LINK" socket. Both cables must be speaker
cables with an appropriate cross-section. As speaker signals have a much higher level than instrument and
line signals, the PAD button must be used to attenuate the volume level. A total of three attenuation levels are
available: -10 dB, -20 dB, -30 dB (both PAD switches pressed down). To avoid clipping, the amplifier power
should not exceed 100 watts.
CAUTIoN!
PoWER AMPLIFIERS USING TUBE TECHNoLoGY ALWAYS NEED A CoRRESPoNDING LoAD AT THE oUTPUT. A
TUBE AMPLIFIER SHoULD NEVER BE CoNNECTED To THE PAN16 WITHoUT A SPEAKER. THIS MIGHT RESULT
MoST LIKELY IN THE DESTRUCTIoN oF BoTH DEVICES.
GnD lift Switch
In conventional microphone cables, the cable shield is connected on both ends of the xLR connector to PIN 1.
This leads to grounding for these devices and as a result may cause the so-called ground loop hum. But since
it is sufficient to connect the ground on one side only for shielding purposes, the "GND LIFT" switch on the
PAN16 enables the separation of the PIN 1 from the ground. This prevents ground loops and associated hum-
ming noises. In practical use, by trial and error, choose the position of the switch which causes the least noise.
GRounDinG of the houSinG of the pan16.
For 19" equipment, grounding of the housing is almost exclusively done through the common rack rail. In
order to avoid duplication of this grounding, the housing is not connected internally to the electronic ground. If
the PAN16 is not installed in a rack, and operating noise occurs, connect the housing for example, via a screw
on the front panel mounting with a suitable mass.
Please do not place the PAN16 in the vicinity of strong alternating magnetic fields, such as power transform-
ers. There is a risk of inducing a hum in the audio transformer.
10

ManufactuReR'S waRRantY

This warranty extends to the Palmer branded product you purchased from Adam Hall. The statutory warranty
rights against the vendor shall not be affected by this warranty. Rather, this warranty gives you additional
independent claims against Adam Hall.
With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall part-
ners, under normal use, are free of defects in material or workmanship for a period of 5 years from the date
of purchase, or 2 years from the date of purchase for tube amplifiers and guitar cabinets. The warranty period
begins on the date of purchase. In order to assert a claim for warranty service, the proof of date of purchase
is provided by the receipt bearing the date of purchase or the date of purchase on the delivery note. You are
entitled to warranty service under the conditions and provisions set out in this document, if a repair within the
warranty period is required.
This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transfer-
able to any person to whom the property is transferred by the original purchaser.
Within the warranty period, the defective parts or the product from Adam Hall will be repaired or replaced.
Under the terms of this warranty, all the replaced or removed components become the property
of Adam Hall.
In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may
decide, at its discretion, to replace this product with a comparable product of at least the same performance.
Adam Hall does not guarantee that the operation of this product will be uninterrupted or error-free. Adam Hall
accepts no responsibility for any damage due to incorrect compliance with the instructions received in the
delivery.
This warranty does not extend to:
• wearing parts (eg battery, tubes).
• devices that have had their serial number removed or damaged, or failed as a result of an accident
• inappropriate or abusive use or other external causes
• devices that were not used in accordance with the operating parameters defined in the user documentation
shipped with the product
• devices that have been repaired using parts not made or distributed by Adam Hall
• devices that have been serviced, modified or repaired by someone other than Adam Hall or an authorise
service partner.
These terms and conditions constitute the complete and exclusive warranty agreement between you and
Adam Hall regarding the Adam Hall branded product you have purchased. This warranty is valid only within
Europe. outside of Europe please contact our official distributors.
11