Black and Decker MFL143 Manual De Instrucciones página 6

ENGLISH
Keep blades sharp. Dull or damaged blades may cause
u
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
When cutting pipe or conduit, make sure that they are free
u
from water, electrical wiring, etc.
Do not touch the workpiece or the blade immediately after
u
operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
u
floors or ceilings, check for the location of wiring and
pipes.
The blade will continue to move after releasing the switch.
u
Always switch the tool off and wait for the saw blade to
@ come to a complete standstill before putting the tool down.
Warning! Contact with, or inhalation of dusts
arising from cutting applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
@ personal injury and/or damage to property.
Warning! Additional safety warnings for sanders
Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
@
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
Thoroughly remove all dust after sanding.
u
Take special care when sanding paint which is possibly
u
lead based or when sanding some woods and metal which
may produce toxic dust:
6
(Original instructions)
Do not let children or pregnant women enter the work
t
area.
Do not eat, drink or smoke in the work area.
t
Dispose of dust particles and any other debris safely.
t
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.