DeWalt DCF896 Traducido De Las Instrucciones Originales página 39

settings that do not overload the tap by driving it too far
before reversing.

WARNING: Use caution not to drive a tap past the end of
its threads, or to bottom a tap in a blind hole.

WARNING: Always follow tap manufacturer's guidelines
for proper tap selection and use with different materials,
cutting fluids, tap drill sizes and feed rates.

WARNING: Tapping mode is not recommended for
use with taps less than 8 mm or more than 20 mm
in diameter.

WARNING: Recommended tapping speeds in Tables 2
and 3 are a suggestion only, based on test results tapping
new threads at 75% thread depth. It is recommended to
perform a test application on scrap material, starting at
speed 1 and working up. Tapping mode should be used in
the lowest speed that results in an appropriate feed rate
and chip clearing for the material.

WARNING: When using advanced tapping mode, always
start with the default forward time and reverse time
shown in Table 4, then increase or decrease as necessary.
When the Precision Tap™ is enabled, the tool will operate in
forward and then automatically operate in reverse without
releasing the trigger. The tool will continue to alternate
between forward and reverse until the trigger is released.
D WALT Tool Connect™ (Fig. A)
e

WARNING: To reduce the risk of injury, remove accessories
from the tool anvil before any Tool Connect™ interaction.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode selector button
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D WALT Tool Connect™ is an optional application for your
e
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific tool
functions. Refer to Tool Connect
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
• Follow the instructions in the app to create your Tool
Connect™ account.
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
9 (Fig. A) to set the tool to the
TM Mode Selector.
• To connect your tool with the D
at the appropriate screen, press the mode selector button
for 3–5 seconds, then wait for the tool to connect. The tool
can only be connected to one Tool Connect™ account at
a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D WALT service centre. Do not attempt to replace the coin cell
e
battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithium salts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
Anvils (Fig. D, E)

WARNING: Use only impact-rated accessories. Non-
impact accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure that it
con tains no cracks.

CAUTION: Inspect anvils, detent pins and hog rings prior
to use. Missing or damaged items should be replaced
before use.
Place the switch in the locked off (centre) position or remove
battery pack before changing accessories.
Anvil with Detent Pin (Fig. D)
DCF896
To install an accessory on the anvil, align the hole in the
side of the accessory with the detent pin
Press the accessory on until the detent pin engages in the hole.
Depression of detent pin may be necessary to aid installation
of accessory.
EnGLIsh
WALT Tool Connect™ app,
e
9
16 on the anvil 3 .
37