Product Description - Blaupunkt 5VF5X00EWE Instrucciones De Uso

PRODUCT DESCRIPTION

1. Upper rack
2. Foldable flaps
3. Upper rack height adjuster
4. Upper spray arm
5. Lower rack
6. Cutlery basket
7. Lower spray arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes
and on the machine's functional components.
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL
indicator light
in the control panel is lit.
1. Remove the lower rack and unscrew
the reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately 1 kg);
it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to avoid
corrosion.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
INSTRUCTION MANUAL
You can download the Safety Instructions and the Instruction Manual, by visiting our website
www.blaupunkt-einbaugeraete.com.
Before using the appliance carefully read Safety Instructions.
13. ON-OFF/Reset button with indicator light
14. Program selection button
15. Salt refill indicator light
16. Rinse Aid refill indicator light
17. Program number and delay time indicator
18. Tablet indicator light
19. Display
20. Half Load indicator lights
21. Half Load button
22. Delay button
23. START/PAUSE button with indicator light / Tab
The factory sets the default value for the water hardness:
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button P for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The current selection level number and the salt indicator light both flash.
• Press button P to select the desired hardness level (see WATER
HARDNESS TABLE).
Water Hardness Table
°dH
Level
German degrees
1 Soft 0 - 6
2 Medium 7 - 11
3 Average 12 - 16
4 Hard 17 - 34
5 Very hard 35 - 50
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL
indicator light switches off.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher
detergent.
13
EN
°fH °Clark
French degrees English degrees
0 - 10 0 - 7
11 - 20 8 - 14
21 - 29 15 - 20
30 - 60 21 - 42
61 - 90 43 - 62