Blaupunkt 5VF5X00EWE Instrucciones De Uso página 14

EN
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when the RINSE AID REFILL indicator light
panel is lit.
B
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button P three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator light flash.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button
Setting is complete!
PROGRAMS TABLE
Program
1. Eco
2. Intensive
3. Mixed
4. Rapid 30'
5. Sanitizing
6. Soak
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature
and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options
and sensor calibration. The sensor calibration can increase program duration up to 20 min.
in the control
A
50°
65°
55°
-
45° -
-
65°
- -
-
If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied.
The LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes, set a mid-
range number (3-4).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C.
Introduce the detergent into the dry dispenser D only.
Place the amount of detergent for pre-washing directly inside the tub.
D
C
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
button, because it adjusts the program so that the best washing
and drying results are always achieved.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
Duration
Available of wash
options program
*)
(h:min)
2:45
2:30
2:00
0:30
1:40
0:10
14
1. When measuring out the detergent
refer to the mentioned earlier
information to add the proper
quantity. Inside the dispenser
D there are indications to help
the detergent dosing.
2. Remove detergent
from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until
the closing device is secured
in place.
Water
consumption
(litres/cycle)
**)
12.0
15.0
15.0
9.0
11.5
4.5
residues
Energy
consumption
(kWh/cycle)
0.95
1.50
1.35
0.50
1.30
0.01