DeWalt DCST5812N Traducido De Las Instrucciones Originales página 34

EnGLIsH
1. Remove battery.
2. Cut a max of 8 m length of trimmer line.
3. Align spool housing eyelets
spool head as shown in Figure H.
16
4. Thread one end of the trimmer line through an eyelet. Guide
the line through to the second eyelet and continue to pull
the line through until there are equal lengths of string on
each side of the spool housing as shown in Figure H.
5. Secure the spool cap 17 from moving with one hand.
Using your other hand, wind the string onto the spool by
rotating the spool head 16
Figure I. Continue winding until 127 mm of string remain on
each side of the spool housing.
Replacing Spool Assembly (Fig. A, J, K)
1. Rotate the spool housing 8
spindle plate aligns with notch
screwdriver through the notch and into the hole, to prevent
the spindle from turning.
2. Uncrew and remove the spool housing by turning the spool
head 16 clockwise.
nOTE: Do not try to remove the spool housing by turning
the spool cap 17 .
3. Remove spindle plate 20
Remove any dirt and grass from the motor housing and
spindle plate.
4. Install spindle plate 20 onto the spindle
D shaped retaining nut 22
base of the spindle plate.
5. Align the spindle plate hole and notch, insert a screwdriver
back into the hole and thread the new spool housing
counterclockwise. Securely tighten the new spool housing
onto the spindle .
21
Replacing Guard (Fig. A, L–N)

WARNING:
Never operate appliance without guard
firmly in place.
1. Remove the spool housing as described in the Replacing
Spool Assembly section.
2. Remove the 4 guard screws
3. Lift the guard off at an angle as shown in Figure M.
4. To attached a new guard, slide the tab
under the lip 25 of the motor housing
back of the guard into place as shown in Figure N.
5. Replace and securely tighten the 4 guard screws
6. Replace the spool housing as described in the Replacing
Spool Assembly section.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING:
To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
32
14 with the arrow 15 on the
counter clockwise as shown in
until the hole 18 in the
19 in the guard. Insert a
before installing a new housing.
21 , so the double
on the spindle sits inside the
23 shown in Figure L.
24 of the new guard
5 , then lower the
23 .
installing attachments or accessories. An accidental
start-up can cause injury.
1. Keep the air intake slots 27
avoid overheating.
2. Your trimmer line can dry out over time. To keep your line in
top condition, store spare line in a plastic, sealable bag with
a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and a
damp rag.
4. The line cutter on the edge of the guard can dull over time.
It is recommended you periodically touch-up the sharpness
of the blade with a file.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING:
Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
, shown in Figure A, clean to
WALT recommended
e