Product Features; Power Button - HoMedics BMSC-3000H-EU Manual De Instrucciones

PRODUCT FEATURES:

1
2
3
INSTRUCTIONS FOR USE:
IMPORTANT - Preparing the appliance for use
The Shiatsu Massager comes with a screw located on the back of the unit to
protect the massage mechanism during shipment, which must be removed
before the first use to allow the shiatsu feature to function. Use the provided
Allen key. Then, properly dispose of the screw.
WARNING – Failure to remove screw may cause permanent damage to
the appliance.
Error: all remote control LEDS flash for a few seconds.
Cause: massager overloaded.
Solution: ensure the allen key bolt/screw has been removed from back of the
massage cushion (using the allen key included). Should the condition continue
after this please contact your HoMedics service centre.
Strapping System
The SensaTouch Shiatsu Back Massager incorporates a unique strapping system
which allows you to fasten it to almost any chair. Just slip the straps over the
seat or chair and adjust fastening straps to secure. Your massager won't slip or
slide away.
Note: Do not use this product for more than 15 mins at a time.
1–Demo Button - For a brief demonstration of
the features of the Shiatsu Massaging Cushion, press
the Demo button. The unit will briefly go through
each function. Once complete, the unit automatically
4
turns off. The L.E.D. light will blink to indicate the
active functions.
Shiatsu Massage - A deeply relaxing and
rejuvenating experience invented in Japan using
rhythmic finger pressure to stimulate 'chi' (vital
energy), relieving stress and tension.
5
2–Shiatsu Programs
- Choose from 3
preset programs where the Shiatsu massage travels
up and down in a specific area of the back. To select
a program, simply press the button and the LED will
illuminate. To deselect, press the button again or
press another button.
= Full Back
= Upper Back
= Lower Back
3–Spot Shiatsu - While the unit is in Shiatsu
6
massage, press either button to stop and focus the
Shiatsu action in one place. Once the unit is operating
in Spot Shiatsu, you may adjust the mechanism
position by holding down either button until the
7
desired position is reached. The Up Arrow will move
the mechanism upwards and the Down Arrow will
move it down. Once you release the button, the
mechanism will stop in that place.
4–Power Button - To turn on the unit, first
press the POWER button. The LED indicator will
illuminate and confirm your selection. To turn off the
unit, simply press the button again. The LED indicator
will blink while the back massage mechanism returns
to its lowest point and then it will turn off.
The actual product materials and fabrics
may vary from the picture shown.
3
Rolling Massage - Rolling is like two hands or
thumbs working up and down your back.
5–Rolling Programs
- Choose from 3 preset
programs where the Rolling massage travels up
and down in a specific area of the back. To select a
program, simply press the button and the LED will
illuminate. To deselect, press the button again or
press another button.
6–Width Adjustment - While the unit is
in Rolling massage for the back, press this button to
adjust the distance or width between the massage
heads. With each press, the massage heads will move
to the next available position.
–Heat
- For soothing heat when massage
7
is on, simply press the heat button and the
corresponding red L.E.D. light will illuminate.
To deselect, press the button again and the
corresponding L.E.D. light will turn off.
For your safety, heat cannot be turned on if massage
is not selected.
NOTE: There is a 15-minute auto shut off on the unit
for your safety.
NOTE: The moving dual massage mechanism on
the back always "parks" or finishes in its lowest
position. It will continue to this position after the
power has been turned off. If the electrical supply is
interrupted, when power is restored, the mechanism
will "park" or move to its lowest position.
Moving Shiatsu
massage mechanism