Chain Saw Safety Warnings - sunjoe SWJ700E Manual Del Operador

This electric chain saw is double-insulated, eliminating the
need for a separate grounding system. Use only identical
replacement parts. Read the instructions before servicing
double-insulated appliances. Use this chain saw only as
described in this manual.
Service
• Have your power tool serviced by a qualified repair
person at an authorized Snow Joe
using only identical replacement parts or call the
Snow Joe + Sun Joe
® ®
1-866-SNOWJOE (1-866-766-9563). This will ensure
that the safety of the power tool is maintained.

Chain Saw Safety Warnings

• Keep all parts of the body away from the saw chain when
the chain saw is operating. Before you start the chain saw,
make sure the saw chain is not in contact with anything. A
moment of inattention while operating the chain saw may
cause entanglement of your clothing or body with the
saw chain.
• Always hold the chain saw with your right hand on the rear
handle and your left hand on the front handle. Holding the
chain saw with a reversed hand configuration increases
the risk of personal injury and should never be done.
• Wear safety glasses and hearing protection. If you are
using the chain saw every day under normal conditions,
you can be exposed to a noise level of 85 dB (A) or higher.
Further protective equipment for head, hands, legs, and
feet is recommended. Adequate protective clothing will
reduce personal injury by flying debris or accidental
contact with the saw chain.
• Do not operate the chain saw in a tree. Operation of a
chain saw while up in a tree may result in personal injury.
• Always keep proper footing and operate the chain saw
only when standing on a fixed, secure, and level surface.
Slippery or unstable surfaces such as ladders may cause
a loss of balance or control of the chain saw.
• When cutting a limb that is under tension, be cautious
of spring back. When the tension in the wood fibers is
released, the spring-loaded limb may strike the operator
and/or throw the chain saw out of control.
• Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
• Carry the chain saw by the front handle with the chain saw
switched off and away from your body. When transporting
or storing the chain saw, always fit the cutting bar sheath.
Proper handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
• Follow instructions for lubricating, chain tensioning, and
changing accessories. An improperly tensioned or poorly
lubricated chain may either break or increase the chance
for kickback.
+ Sun Joe dealer
® ®
customer service center at
• Keep handles dry, clean, and free from oil and grease.
Greasy, oily handles are slippery and can cause loss
of control.
• Cut wood only. Do not use the chain saw for any other
purpose. For example, do not use the chain saw to cut
plastic, masonry, or non-wood building materials. Using
the chain saw in these incorrect ways could result in
serious damage to you and your tool.
Causes and Prevention
of Kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut. Tip contact in some cases may cause
a sudden reverse reaction, kicking the guide bar up and back
towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the
saw which could result in serious personal injury. Do not rely
exclusively upon the safety devices built into your saw.
As a chain saw user, you should take several steps to keep
your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as detailed below:
• Maintain a firm grip (right hand on the rear handle and
left hand on the front handle with thumbs and fingers
encircling the respective handles) and position your body
and arms to allow you to resist kickback forces. Kickback
forces can be controlled by the operator if proper
precautions are taken. Do not let go of the chain saw.
• Do not overreach and do not cut above shoulder height.
This helps prevent unintended tip contact and enables
better control of the chain saw in unexpected situations.
• Only use replacement bars and chains specified by the
manufacturer. Incorrect replacement bars and chains may
cause chain breakage and/or kickback.
• Follow the manufacturer's sharpening and maintenance
instructions for the saw chain. Decreasing the depth
gauge height can lead to increased kickback.
• Always observe the safety regulations and follow the
correct sawing techniques.
4
KICKBACK DANGER ZONE
R