General Safety; Battery Charger Safety; Product Familiarisation; Intended Use - Silverline 511273 Manual De Instrucciones

511273

General Safety

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including children) with reduced,
physical or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
NOTE: The term "residual current device (RCD)" may be replaced by the term "ground fault circuit
interrupter (GFCI)" or "earth leakage circuit breaker (ELCB)".
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce
dust-related hazards.
5W Lithium Rechargeable Torch

Battery Charger Safety

Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting
to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your battery
charger clean; foreign objects or dirt may cause a short or block air vents. Failure to follow these
instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
WARNING: Do not recharge non-rechargeable batteries
Torch Safety
When the torch is switched on, the following must be observed:
• Do not look directly into the lens
• Do not shine into a person's or animal's eyes
• Do not point the beam at cars, motorcycles, aircraft, ships or any other vehicle or machinery
that is operated by a person. Bright light can cause temporary blindness and could result in
a serious accident

Product Familiarisation

1 Bulb
2 Lens Ring
3 Handle Lock Button
4 Strap Link (x 2)
5 Carry Strap
6 Pistol Handle
7 ON/OFF Switch
8 Mains Charger
9 12V Charger
10 Adjustable D-Stand/Handle

Intended Use

Rechargeable torch for domestic use.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
IMPORTANT: The sealed lithium battery in this product will be drained from storage. The following
steps must be taken to ensure it is charged correctly. This will maximise the performance and
working life of the battery:
• Press the ON/OFF Switch (7) and check to see when the torch is ON
• NOW MAKE SURE the product is switched OFF. The torch will only charge in the OFF position
• Plug the Mains Charger (8) in to the mains power supply, and plug the small end into the
charging socket
• Leave to charge for a MINIMUM of 5 hours before first use
Note: If the torch fails to charge repeat the above, ensuring that the Switch (7) is in the OFF position.
Fitting the Carry Strap
• Prise apart the Strap Links (4) and remove them from the torch body
• Thread them through the ends of the Strap (5)
• Re-fit the Strap Links (4) to the torch body. Squeeze together tightly and check that
they are secure
silverlinetools.com
5