Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) A/C button housing • D) Pocket • E) Console bracket • F) #8 x 3/8" Phillips pan-head screws (6)
• G) Panel clips (2) • H) Climate extension harness (not shown) • I) Axxess interface and harness (not shown)
A
B
The World's best kits.
®
Dodge Journey 2011-2020
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Included interface retains factory screen
• Painted matte black to match factory finish
Note: Does not retain sound from "Driver Convenience Group"
C
D
F
MetraOnline.com
E
G
© COPYRIGHT 2022 METRA ELECTRONICS CORPORATION
99-6520B
I N S TA L L AT I O N I N S T R U C T I O N S
U.S. Patent # D755,778 D768,126
TABLE OF CONTENTS
Dash Disassembly . ..............................................2-3
Kit Preparation . ......................................................4
Kit Assembly
– ISO DIN radio provision with pocket . ................5
– ISO DDIN radio provision . ...................................5
Axxess interface installation . ...........................6-12
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Interface and harnesses included
Antenna Adapter: 40-EU10 (sold separately)
AXXESS Steering Wheel Control Interface (sold
separately)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections, especially the air bag
indicator light, must be secure before cycling
the ignition to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
REV. 4/19/22 INST99-6520B
Publicidad
Capítulos
Tabla de contenido
Manuales relacionados para Metra 99-6520B
Resumen de contenidos para Metra 99-6520B
- Página 1 99-6520B I N S TA L L AT I O N I N S T R U C T I O N S U.S. Patent # D755,778 D768,126 Dodge Journey 2011-2020 TABLE OF CONTENTS Dash Disassembly ..........2-3 Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications. Kit Preparation ............4...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Using the panel removal tool, carefully unclip and remove the trim panel along the top of the glove box over to the passenger’s side A/C vent. (Figure A) 2. Unsnap and remove the small trim panel to the left of the hazard button. (Figure A) 3. Remove (2) Phillips screws securing the radio/climate control panel, then unclip, unplug and remove the panel. (Figure B) Note: A climate extension harness is (Figure A) (Figure B) provided to relocate the climate controls to a lower position in the center console. 4. Remove (4) Phillips screws securing the radio chassis. Slide the chassis out, then unplug and remove the chassis. (Figure C) Note: The white 4-pin harness will be reused in Kit Assembly. Continued on the next page (Figure C) (Figure D) 386.257.1187 MetraOnline.com... - Página 3 DASH DISASSEMBLY (CONT) 5. Pull up on shift knob to remove. (Figure D). 6. Unclip and remove the shifter trim panel, including the cup holders from the top of the center console. (Figure E) 7. Push down and then pull back and out on the pocket in the front of the console. (Figure F) Note: You may need to pull the console side panels outward at the same time as pulling out on pocket. (Figure D) (Figure E) (Figure F) 8. Remove the (2) metal panel clips on the front side of the pocket and save for Kit Preparation. Continue to Kit Preparation REV. 4/19/22 INST99-6520B...
-
Página 4: Kit Preparation
KIT PREPARATION 1. Attach the console bracket to the back of the A/C button housing using (4) #8 x 3/8" Phillips screws provided with this kit. (Figure A) 2. Install the (2) metal panel clips saved from the pocket disassembly onto the console bracket. (Figure A) 3. Using the climate extension harness provided with this kit, connect the A/C button housing assembly to the factory wiring harness in the vehicle. 4. Secure the A/C button housing into the pocket space in the front of the center (Figure A) (Figure B) console. (Figure B) Continue to Kit Assembly 386.257.1187 MetraOnline.com... -
Página 5: Kit Assembly
KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Secure the radio brackets to the pocket 1. Break the small locating pin from the using the (2) #8 x 3/8" Phillips screws inside surface of each bracket. provided with this kit. (Figure A) (Figure A) Note: Pins on the brackets will align 2. Secure the radio brackets to the radio with the front mounting hole of pocket. using the screws supplied with the 2. Remove the metal DIN sleeve and trim radio. (Figure A) ring from the aftermarket radio. Remove pin Continue to Axxess Interface Installation 3. Slide the radio into the bracket/pocket assembly, then secure it to the assembly (Figure A) (Figure A) using the screws supplied with the... -
Página 6: Tabla De Contenido
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES TABLE OF CONTENTS • Provides accessory power (12-volt 10-amp) Connections .............................. 7 • Retains R.A.P. (retained accessory power) Installation ...............................8 • Used in amplified and non-amplified systems Programming ............................8 • Provides NAV outputs (parking brake, reverse, V.S.S.) Final Assembly ............................8 • Prewired for an AXXESS steereing wheel control interface Audio Level Adjustment ..........................8 • Retains balance and fade Screen Operation ..........................9-11 • Ability to add an aftermarket backup camera or additional video input Updating The Interface ...........................12 • Retains the factory display screen • Micro “B” USB updatable Note:... -
Página 7: Connections
CONNECTIONS From the 16-pin harness with stripped leads to the aftermarket radio, connect as indicated: From the 6520 harness continued... • Red wire to the accessory wire. • Green/Black wire to the left rear (-) speaker output. Note: If also installing an AXXESS steering wheel control interface (sold separately, there will • Purple wire to the right rear (+) speaker output. be a Red wire on the 6520 harness to connect as well. • Purple/Black wire to the right rear (-) speaker output. • Orange/White wire to the illumination wire, if applicable. • Yellow RCA jack labeled (2) to either an aftermarket backup camera, or an AUX video input. • Blue/White wire to the amp turn-on wire, if equipped with a factory amplifier. Disregard the Yellow RCA jack labeled (1), it will not be used in this application. The following (3) wires are for aftermarket multimedia/navigation radios that require these wires: Note: There is also a set of Green, Green/Black, Violet, Violet/Black wires coming from the Black 18-pin connector that goes to the interface, tape off and disregard these wires, they will... -
Página 8: Installation
Attention! For models with a 8-inch screen, update the interface via the Axxess Updater available 1. Secure the completed assembly to the dash using the factory hardware. at axxessinterfaces.com. Select “8-inch screen” once prompted to. Instructions to update the 2. Attach the (2) panel clips provided to the 99-6520B radio trim panel, then reassemble the interface are available at the end of this instruction booklet. dash in reverse order of disassembly using the 99-6520B panel. -
Página 9: Screen Operation
FACTORY 4.3 INCH SCREEN OPERATION 1. Radio button – Show the current time 2. Player button – Not used in this application 3. Climate button – Takes you to the climate screen 4. Setting button – Takes you to the setting screen 5. More button – Shows the outside temperature and current time 6. Screen Off – Turns the display off REV. 4/19/22 INST99-6520B... - Página 10 FACTORY 4.3 INCH SCREEN VIDEO OPTIONS MENU Once in the setting screen, scroll down • Not Used to the Customize button. Pressing the • Back-up (Backup Camera) is controlled by button will take you to the video option data and will only activate when you screen. (Figure A) put the vehicle in reverse. 2. Once in the customize menu, you can • AUX input is controlled by data and will select to make the Video Input 2 either: only work while the vehicle is in park. (Figure B) (Figure C) (Figure A) (Figure C) 3. After you have made your selection, tap the “Done” button located on the upper left hand corner of the screen to exit. 4. The About button will display the current software of the kit, and also the VIN of the vehicle. (Figure D) (Figure B) (Figure D) 386.257.1187 MetraOnline.com...
- Página 11 FACTORY 8 INCH SCREEN OPERATION 1. Enter the settings menu by tapping the 2. Once in the setting menu, scroll down 3. Once in the customize menu, you can 4. Tapping the About button will display the select to make the Video Input 2 either: gear icon in the upper left corner of the and tap the Customize button to enter the current version number of the kit, and screen. customize menu. the VIN number of the vehicle. Tap the • Not Used OK button to exit. • Reverse (Backup Camera) is controlled by 5. After you have made your selection, tap data and will only activate when you put either the X or Back (left arrow) button the vehicle in reverse. one time to return to the previous menu, • AUX input is controlled by data and will or two times to return to the main menu. only work while the vehicle is in park.
-
Página 12: Updating The Interface
Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. MetraOnline.com ®... -
Página 13: Indice
NOTA: Consulte también las instrucciones incluidas con la radio de mercado secundario. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 4/19/22 INST99-6520B... -
Página 14: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel de la moldura a lo largo de la parte superior de la guantera sobre la rejilla de aire acondicionado del lado del pasajero. (Figura A) 2. Desenganche y quite el panel de moldura pequeño a la izquierda del botón de las luces intermitentes. - Página 15 DESMONTAJE DEL TABLERO (CONT) 5. Jale hacia arriba la perilla de la palanca de velocidades para quitarla. (Figura D) 6. Desenganche y quite el panel de la moldura de la palanca de velocidades, incluyendo los portavasos de la parte superior de la consola central. (Figura E) 7.
-
Página 16: Preparación Del Kit
PREPARACIÓN DEL KIT 1. Una el soporte de la consola a la parte posterior de la carcasa del botón de aire acondicionado con (4) de los tornillos Phillips #8 x 3/8" proporcionados. (Figura A) 2. Instale los (2) ganchos metálicos del panel que guardó... -
Página 17: Ensamble Del Kit
ENSAMBLE DEL KIT Provisión de radio ISO DIN con bolsillo Provisión de radio ISO DDIN 1. Atornille los soportes del radio al 1. Quiebre el pequeño pin que está en la cavidad con los (2) tornillos Phillips #8 superficie interior de cada soporte. de 3/8"... -
Página 18: Instalación De La Interfase Axxess
INSTALACIÓN DE LA INTERFASE AXXESS CARACTERÍSTICAS DE LA INTERFASE INDICE • Provee corriente de accesorios (12 voltios 10 amperes) Conexiones ............................... 7 • Retiene R.A.P. (corriente de accesorio retenida) Instalación ..............................8 • Se usa en sistemas amplificados y no amplificados Programación ............................8 •... -
Página 19: Conexiones
CONEXIONES Del arnés de 16 pines con conectores pelados al radio de mercado secundario: Desde el arnés 6520 al radio de mercado secundario (cont.): • Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera. • Conecte el cable rojo al cable de accesorios. •... -
Página 20: Instalación
Axxess disponible en axxessinterfaces.com. Seleccione “pantalla de 8 pulgadas” 2. Conecte los (2) clips del panel provistos al panel de moldura de radio 99-6520B, luego una vez que se le solicite. Las instrucciones para actualizar la interfaz están disponibles al final de vuelva a armar el tablero en el orden inverso al de desmontaje usando el panel 99-6520B. -
Página 21: Fábrica 4.3 Pulgadas Operación De Pantalla
FÁBRICA 4.3 PULGADAS OPERACIÓN DE PANTALLA 1. Botón de radio – Muestra la hora actual 2. Botón de reproducción – no se utilizará en esta aplicación. 3. Botón de clima – Lo lleva a la pantalla de clima 4. Botón de configuración – Lo lleva a la pantalla de configuración 5. - Página 22 FACTORY PANTALLA DE 4.3 PULGADAS MENÚ DE OPCIONES DE VÍDEO Una vez en la pantalla de configuración, 3. Después de haber hecho su selección, desplácese hacia abajo al botón toque el botón “Hecho” ubicado en la Personalizar. Presionando el El botón parte superior esquina izquierda de la te llevará...
-
Página 23: Funcionamiento De La Pantalla De Fábrica De 8 Pulgadas
FUNCIONAMIENTO DE LA PANTALLA DE FÁBRICA DE 8 PULGADAS 1. Ingrese al menú de configuración 2. Una vez en el menú de configuración, 3. Una vez en el menú de personalización, 4. Al tocar el botón Acerca de, se mostrará puede seleccionar hacer la Entrada de tocando el ícono de ajustes en la esquina desplácese hacia abajo y toque el botón... -
Página 24: Actualizando
800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). The World’s best kits. MetraOnline.com ® © COPYRIGHT 2022 METRA ELECTRONICS CORPORATION REV. 4/19/22 INST99-6520B...