Triton T20CH Instrucciones De Uso Y De Seguridad página 6

d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
Battery tools use and care
a) Recharge only with charger specified by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of fire when used with another battery
pack.
b) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire
c) When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws and other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause a burns or
a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contact eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
Additional Safety for Battery-
Operated Drills & Screwdrivers
For safety relating to protective clothing/equipment and general health hazards relating to
power tools; refer to General and Electrical Safety sections in this manual
• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss
• Hold power tools by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring. Cutting accessory and/or fasteners
contacting a "live" wire may make exposed metal parts of the power tool "live" and give
the operator an electric shock.
Important: It is imperative to follow all national safety regulations concerning installation,
operation and maintenance
• Do not allow anyone under the age of 18 years to use this tool, and ensure that operators
are qualified and familiar with the operating and safety instructions
• If batteries are to be charged outdoors, ensure that the power supply and charger are
protected against weather/moisture
• When using the drill, use safety equipment including safety glasses or shield, ear
defenders, and protective clothing including safety gloves. Wear a dust mask if the drilling
operation creates dust
• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid
touching live components or conductors
• Ensure that the lighting is adequate
• Ensure that the drill bit is securely fixed in the chuck. Insecure drill bits can be ejected
from the machine causing a hazard
• Ensure that the drill bit is in contact with the workpiece prior to starting up the tool
• Before drilling, check that there is sufficient clearance for the drill bit under the workpiece
• Do not put pressure on the tool, to do so would shorten its service life
• Drill bits get hot during operation, allow to cool prior to handling them
• Never use your hands to remove sawdust, chips or waste close by the bit
• If you are interrupted when operating the drill, complete the process and switch off before
looking up
• Where possible, use clamps or a vice to hold your work
• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired
by a qualified service centre
• Always wait until the drill has come to a complete stop before putting it down
• Periodically check all nuts, bolts and other fixings and tighten where necessary
940454_Z1MANPRO1.indd 5
Battery and Charger Safety
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting
to charge the battery pack.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your
battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure
to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard
• Children should be supervised to ensure that they do not play with the appliance.
Warning: Do not recharge non-rechargeable batteries
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this
power tool, or others recommended by the supplier. Keep batteries clean; foreign objects
or dirt may cause a short. Allow batteries to cool for 15 minutes after charging or heavy
use. Failure to follow these instructions may cause overheating or fire.
• When not in use batteries should be stored at room temperature (approx. 20˚C). Ensure
that batteries cannot accidentally short in storage.
NOTICE for Battery Packs
• DANGER – Risk of battery packs include burn hazard, fire hazard and explosion hazard
• CAUTION - Do Not Open, Disassemble, Crush, Heat above 60 degree C or incinerate. Do
Not dispose of in fire or similar.
• CAUTION – for Primary batteries, do not charge.
• CAUTION – only charge battery with charger model T20BC. For Safety use of battery
charger, make reference to the instruction manual of the battery charger.
• CAUTION - Follow Manufacturer's Instructions
Battery and charger safety features
The battery pack and charger are fitted with a number of safety features which may be
triggered during charging or operation:
• Over-charge protection: Charger automatically switches off when the battery pack has
reached full charge capacity, protecting the internal components of the battery pack
• Over-discharge protection: Prevents the battery from discharging beyond the
recommended lowest safety voltage
• Over-heat protection: Sensor switches off if the battery becomes too hot during operation.
This can happen if the tool is overloaded or being used for extended periods of time. Up to
30 minutes cooling time may be required depending on the ambient temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current
draw is exceeded, protecting the internal components. The battery will resume normal
operation when the current draw returns to a normal safe level. This may take a few
seconds
• Short circuit protection: The battery pack will stop working immediately if a short circuit
occurs, this prevents damage to the battery pack or tool
WARNING for Australia and New Zealand
• WARNING: When used in Australia or New Zealand, it is recommended that this tool is
ALWAYS supplied via Residual Current Device (RCD) with a rated residual current of
30mA or less.
GB
5
25/09/2014 17:25