Panasonic AW-HS50E Instrucciones De Operación página 16

1. Parts and their functions
 A bus crosspoint buttons [1 to 5]
 B bus crosspoint buttons [1 to 5]
These are used to select the materials to be output
to the PGM bus, PST bus, AUX bus, PinP bus and
KEY-F/S bus.
When a button is pressed and the material
allocated to that button is selected, the indicator of
the button lights.
Depending on the status of the BUS DELEGATION
button () indicators, the operation performed
differs as follows.
1. While the indicators of all three buttons are
off:
When one of the crosspoint buttons is pressed,
the materials of the buses which execute the
background transitions are selected.
[B bus crosspoint buttons]
These are used to select the PST bus
materials.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
[A bus crosspoint buttons]
These are used to select the PGM bus
materials.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
 Memo 
Using the OSD menu, A/B, PGM(A)/PST(B) or
PGM(B)/PST(A) can be selected as the bus mode.
The description given above applies when the
PGM(A)/PST(B) has been selected.
 Refer to "1-1-4. Selecting the bus mode"
(<Operations and Settings> Operating
Instructions).
2. When the indicator of the AUX button is
blinked:
When one of the crosspoint buttons is pressed,
the AUX bus material is selected.
[B bus crosspoint buttons]
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
[A bus crosspoint buttons]
When a button from [1] to [5] is pressed,
PGM, PVW, KEY OUT, CLN or MV is selected
respectively.
3. While the indicator of the PinP button is
blinked:
When a B crosspoint button is pressed, the PinP
bus material is selected.
[B bus crosspoint buttons]
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
4. While the indicator of the KEY-F/S button is
blinked:
When one of the crosspoint buttons is pressed,
the key fill bus or key source bus material is
selected.
[B bus crosspoint buttons]
These are used to select the key fill bus
materials. When a button from [1] to [5]
is pressed, the material assigned to the
corresponding XPT1 to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
[A bus crosspoint buttons]
These are used to select the key source bus
materials.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
15 (E)