Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
RECOMMENDED INSTALLATION FOR ALL APPLICATIONS
(1) Electrical wiring and protection must be in accordance with National
Electrical Code and any other applicable state and local electrical
requirements.
(2) Install proper Zoeller unicheck (combination union and check valve),
preferably just above the basin (indoor installations) to allow easy
removal of the pump for cleaning or repair. If high head or below cover
installation is required use 30-0164 on 1½" (DN40) pipe, 30-0152 on 2"
(DN50) pipe and 30-0160 on 3" (DN80) pipe.
(3) All installations require a basin cover to prevent debris from falling into
the basin and to prevent accidental injury.
(4) When a Unicheck is installed, drill a
discharge pipe even with the top of the pump. NOTE: THE HOLE
MUST ALSO BE BELOW THE BASIN COVER AND CLEANED
PERIODICALLY. (High Head unit see #3 under "Caution" on front page).
Water stream will be visible from this hole during pump run periods.
GATE OR BALL VALVE
10
UNICHECK
2
FULLSIZE DISCHARGE PIPE
6
VENT
13
BASIN LID
3
BASIN
7
GRINDER PUMP
8
9
All installations must comply with all applicable
electrical and plumbing codes.
Model 800 shown.
PUMP PERFORMANCE CURVE
MODEL 800/803/805/807
60
18
55
16
50
807
14
45
40
12
805
35
10
30
803
8
25
800
20
6
15
4
10
2
5
0
5
10
15
20
GALLONS
LITERS 0
20
40
60
80
FLOW PER MINUTE
/
" (5 mm) dia. hole in the
3
16
INSTALLATION SKETCHES
1
GAS TIGHT SEALS
12
TAPE OR CLAMP
3/16" DIA. WEEP HOLE
PIGGYBACK FLOAT
11
10cm (4") OF GRAVEL
SK3012
PERFORMANCE DATA
Shut-off Head:
25
30
35
40
45
50
100
120
140
160
180
© Copyright 2015 Zoeller
(5) Securely tape or clamp power cord to discharge pipe, clear of the float
mechanism(s).
(6) Use full-size discharge pipe.
(7) Basin must be in accordance with applicable codes and
specifications.
(8) Pump must be level and float mechanism(s) clear of sides of basin before
starting pump.
(9) Basin must be clean and free of debris after installation.
(10) Gate Valve or Ball Valve to be supplied by installer and installed
according to any and all codes.
(11) For nonautomatic pumps, locate float switches as shown in sketches. The
best place for the "off" point is above the motor housing and positioned
180° from the inlet. Never put "off" point below discharge on pump
(12) Gas tight seals required to contain gases and odors.
(13) Vent gases and odors to the atmosphere through vent pipe.
TYPICAL FLOAT HANGER ON STEEL COVER PITS
5
4
PEA GRAVEL
On some installations it may be desirable to install an independent hanger
for the level control switches to avoid possible hang ups on the pumps,
piping, valves, etc. Float hangers are available from Zoeller Company on
Catalog Sheet FM0526 or can be fabricated from standard pipe and fittings.
TOTAL DYNAMIC HEAD/FLOW
TOTAL DYNAMIC HEAD/FLOW
MODEL
800
MODEL
800
Feet
Meters
Gal.
Liters
5
1.5
46
174
Feet
Meters
Gal.
Liters
10
3.0
38
144
5
1.5
46
174
20
6.1
18
68
30
9.1
--
--
10
3.0
38
144
40
12.2
--
--
20
6.1
18
68
50
15.2
--
--
30
Shut-off Head:
9.1
--
26 ft. (8.1m)
--
40
12.2
--
--
50
15.2
--
--
26 ft. (8.1m)
Co. All rights reserved.
®
3
ACCESS COVER
PVC OR LIGHT WEIGHT
STAINLESS STEEL PIPE
PER MINUTE
PER MINUTE
SEWAGE
SEWAGE
803
805
807
803
805
Gal.
Liters
Gal.
Liters
Gal.
Liters
35
132
40
151
45
170
Gal.
Liters
Gal.
Liters
31
117
37
140
42
159
35
132
40
151
22
83
29
110
35
132
9
34
20
76
27
102
31
117
37
140
--
--
8
30
18
68
22
83
29
110
--
--
--
--
7
26
35 ft. (10.7m)
9
34
45 ft. (13.7m)
20
55 ft. (16.8m)
76
--
--
8
30
--
--
--
--
35 ft. (10.7m)
45 ft. (13.7m)
STANDARD PIPE
FLANGE
SK1217
807
Gal.
Liters
45
170
42
159
35
132
27
102
18
68
7
26
55 ft. (16.8m)
153604
Publicidad
Tabla de contenido
