Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Before installation, read the following instructions carefully.
Failure to follow instruction and safety information could
cause serious bodily injury, death and/or property damage.
Each Ashland Pump is individually factory tested to ensure
proper performance. Closely following these instructions
will eliminate potential operating problems assuring years
of trouble-free service.
Most accidents can be avoided by using common
sense.
IMPORTANT - Ashland Pump is not responsible
for losses, injury or death resulting from failure
to observe these safety precautions, misuse,
abuse or misapplication of pumps or equipment.
DANGER
All returned products must
be cleaned, sanitized, or
decontaminated prior to shipment, to
insure employees will not be exposed to
health hazards in handling said materials. All
applicable laws and regulations shall apply.
WARNING
Bronze/brass fitted pumps may
contain lead levels higher than considered safe for
potable water systems. Government agencies have
determined that leaded copper alloys should not be
used in potable water applications.
WARNING
Installation, wiring, and junction
connections must be in accordance with the National
Electric Code and all applicable state and local codes.
Requirements may vary depending on usage and
location.
WARNING
Installation and servicing is to be
conducted by qualified personnel only.
DANGER
Rotating machinery,
amputation or severe lacerations can
result. Keep clear of suction and dis
charge openings. DO NOT insert
fingers into pump with power connected.
WARNING
Always wear eye protection when
working on pumps. Do not wear loose clothing that may
become entangled in moving parts.
DANGER
Pumps build up heat and pressure
during operation. Allow time for pumps to cool before
handling or servicing.
DANGER
Hazardous Voltage can shock,
burn or cause death. This pump is not
intended for use in swimming pools or
water installations where human contact with
pumped fluid is possible.
DANGER
Risk of electrical shock. To reduce
risk of electrical shock, always disconnect
pump from source before handling.
Lock out power & tag.
Effluent Pumps
Model: EP40 & EP45 Series
General Safety Information
WARNING
factures recommended maximum performance, as this
could cause the motor to overheat.
WARNING
or disease. Wear adequate protective clothing when
working on a used pump or piping. Never enter a basin
after it has been used.
WARNING
waste disposal unit or toilet: Seafood Shells, Aquarium
Gravel, Cat Litter, Plastic Objects, Sanitary Napkins or
Tampons, Diapers, Rags, Disposable Wipes or Cloth,
Medications, Flammable Material, Oil or Grease, Strong
Chemicals, Gasoline.
•
Operation against a closed discharge valve will cause
premature bearing and seal failure on any pump.
•
Any wiring of pumps should be performed by a
qualified electrician.
•
Cable should be protected at all times to avoid
punctures, cuts, bruises, and abrasions-inspect
frequently.
•
Never handle connected power cords with wet hands.
•
Never let cords or plugs lie in water outside the sump
pit.
•
These pumps are offered in a three phase and single
phase wiring configuration. Voltages will vary
according to the application and can be seen in the
tables in this manual.
2
Do Not use these pumps in water
over 145°F. Do not exceed manu-
Make sure lifting handles are securely
CAUTION
fastened each time before lifting.
DANGER
Do not lift, carry or hang pump by
the electrical cables. Damage to
the electrical cables can cause shock, burns or
death. Never handle connected power cords
with wet hands. Use appropriate lifting device.
Effluent pumps often handle
materials which could cause illness
DANGER
Failure to permanently ground the
pump, motor and controls before
connecting to power can cause shock, burns
or death.
These pumps are NOT to be
DANGER
installed in locations classified
as hazardous in accordance with the
National Electric Code, ANSI/NFPA 70.
Do not introduce into any sewer,
either directly, or through a kitchen
Publicidad
Tabla de contenido
