Hilti NURON NCR 60 D-22 Manual Del Usuario página 9

precautions for working in proximity to electrically live cables or equipment applicable in your country
must be implemented and observed.
▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.
External metal parts of the product could give you an electric shock or cause an explosion if you
accidentally damage an electric cable or a gas or water pipe.
▶ Do not crimp live parts, i.e. parts carrying electric voltage. The crimping tool must be considered as being
uninsulated and must therefore be used in combination with personal protective equipment (protective
gloves, protective footwear, protective clothing, etc.) of a type suitable to provide protection for yourself
and other persons in the vicinity. It is essential to ensure adequate insulation for working in the vicinity of
electrically live lines, for example by the use of solid insulating material or maintenance of an adequate
air gap. Among other uses, the crimping tool is suitable for use on electrically insulating aerial lifts or
platforms.
▶ In order to use the crimping tool in the vicinity of electrically live lines, the user must:
▶ take all different potentials (voltages) into account.
▶ make sure that all chosen measures and tools are appropriate for the application.
▶ be trained for working on electrically live lines.
▶ wear fit-for-purpose personal protective equipment.
▶ wear appropriate, close-fitting clothing.
▶ remove metallic lifestyle accessories such as jewelry.
Power tool use and care
▶ After approx. 50 consecutive crimping operations, switch the power tool off and allow it to cool down for
about 15 minutes. Overheating can lead to damage to the crimping tool.
▶ Store the crimping tool in a dry place inaccessible to children and unauthorized persons.
▶ Hilti recommends having the crimping tool overhauled by Hilti Service after 15,000 crimping operations.
2.3 Battery use and care
▶ Comply with the following safety instructions for the safe handling and use of Li-ion batteries.
Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶ Use only batteries that are in perfect working order.
▶ Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely
harmful to health!
▶ Do not under any circumstances modify or tamper with batteries!
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
▶ Never use or charge a battery that has suffered an impact or been damaged in any other way. Check
your batteries regularly for signs of damage.
▶ Never use recycled or repaired batteries.
▶ Never use the battery or a battery-operated power tool as a striking tool.
▶ Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This
can lead to explosions.
▶ Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.
This can damage the battery and also cause material damage and personal injury.
▶ Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,
electric shock, burns, fire and explosions.
▶ Use only chargers and power tools approved for the specific battery type. Read and follow the relevant
operating instructions.
▶ Do not use or store the battery in explosive environments.
▶ If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to
cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the
document entitled "Instructions on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
→ page 11
Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning
the QR code at the end of these operating instructions.
*2321725*
2321725 English 5