Hilti SCO 6-A22 Manual Del Usuario página 21

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Additional safety instructions for cut-out tools
Personal safety
▶ Use the product and accessories only when they are in perfect working order.
▶ Never tamper with or modify the product or accessories in any way.
▶ Always hold the product with both hands on the grips provided. Keep the grips clean and dry.
▶ Do not touch rotating parts – risk of injury!
▶ Wear eye protection, a hard hat and ear protection and suitable respiratory protection while the product
is in use.
▶ Do not look directly into the light source (LED) of the product and do not aim the beam at other persons'
faces. Risk of dazzling or eye damage.
▶ Never touch the clamping nut or collet when the accessory tool gets stuck and stalls.
▶ Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High
vibration during long periods of work can lead to disorders of the blood vessels and nervous system in
the fingers, hands and wrists.
▶ The product is not intended for use by debilitated persons who have received no special training. Keep
the product out of reach of children.
▶ If work involves break-through, always secure the area on the side opposite where the work is carried
out. Pieces of debris could drop out and/or fall down and injure other persons.
▶ Slits cut into load-bearing walls or other structures can influence the statics of the structure, especially
when reinforcing bars or load-bearing components are cut. Consult the responsible structural engineer,
architect or person in charge of the building project before starting work.
▶ Before switching on the product, check that the collet is fitted and that the clamping nut is tightened.
▶ Use only accessory tools with the correct shank diameter and of a type suitable for the speed of the
product.
▶ Make sure that the accessory tools used have a mounting system compatible with the product and that
they are correctly engaged in the chuck.
*2194405*
2194405 English 15