Panasonic SC-HC38 Instrucciones De Funcionamiento página 12

Radio
A beat sound or noise is heard while receiving
radio broadcast.
≥ Confirm the antenna is properly connected. (l 5)
≥ Adjust the position of the antenna.
≥ Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥ Try using an outdoor antenna if there are buildings or mountains
nearby.
≥ Switch the television or other audio players off or separate it from
this unit.
≥ Keep this unit away from mobile phones if the interference is
apparent.
iPod/iPhone/iPad operations
Cannot charge or operate.
≥ Have you selected the appropriate selector?
Press [iPod] to select either "IPOD_DOCK" or "IPOD_PORT".
≥ Check that the iPod/iPhone/iPad is connected properly. (l 6)
≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/
iPhone/iPad, and then operate again.
≥ Connect the iPod/iPhone/iPad again or try to restart the iPod/
iPhone/iPad.
≥ When this unit is in standby mode, charging will not start when
using the "IPOD_PORT" connection.
Turn this unit on and make sure the charging has started before
switching this unit to standby mode.
Bluetooth
®
Pairing cannot be done.
≥ Check the Bluetooth device condition.
®
The device cannot be connected.
≥ The pairing of the device was unsuccessful or the registration has
been replaced. Try pairing the device again. (l 7)
≥ This unit might be connected to a different device. Disconnect the
other device and try pairing the device again. (l 7)
The device is connected but audio cannot be heard
through this unit.
≥ For some built-in Bluetooth
output to "SC-HC38" manually. Read the operating instructions for
the device for details.
The sound is interrupted.
≥ The device is out of the 10 m communication range. Bring the
Bluetooth ® device closer to this unit.
≥ Remove any obstacle between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band (wireless
router, microwaves, cordless phones, etc.) are interfering. Bring
the Bluetooth ® device closer to this unit and distance it from the
other devices.
≥ Select "MODE 1" for stable communication. (l 7)
12
RQT9746
All manuals and user guides at all-guides.com
devices, you have to set the audio
®
Remote control
The remote control doesn't work properly.
≥ The remote control and this unit are using a different code.
(l 13, "REMOTE ")
≥ Is the battery depleted or is the battery inserted incorrectly? (l 4)
Messages
The following messages or service numbers may
appear on the unit's display.
"--:--"
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 10).
"ADJUST CLOCK"
≥ Clock is not set. Adjust the clock accordingly.
"ADJUST TIMER"
≥ Play timer is not set. Adjust the play timer accordingly.
"AUTO OFF"
≥ The unit has been left unused for about 30 minutes and will shut
down within a minute. Press any button to cancel it.
"CANNOT SET"
≥ Select an audio source other than "BLUETOOTH".
"CHECKING CONNECTION"
≥ The unit is checking the connected iPod/iPhone/iPad.
≥ If this display keeps appearing, make sure that the battery of the
iPod/iPhone/iPad is not depleted and that the iPod/iPhone/iPad is
turned on and connected correctly (l 6).
"ERROR"
≥ Incorrect operation is performed. Read the instructions and try
again.
"F " (" " stands for a number.)
≥ There is a problem with this unit.
Note down the displayed number, disconnect the AC mains lead
and consult your dealer.
"ILLEGAL OPEN"
≥ Sliding door is not in correct position. Turn the unit off and on
again. If this display appears again, consult the dealer.
"IPOD_DOCK OVER CURRENT ERROR"
"IPOD_PORT OVER CURRENT ERROR"
≥ The iPod/iPhone/iPad is drawing too much power. Disconnect the
iPod/iPhone/iPad and turn the unit off and on again.
≥ The USB device is drawing too much power. Switch to "CD"
mode, remove the USB and turn the unit off.
"NODEVICE"
≥ The iPod/iPhone/iPad device is not inserted correctly. Read the
instructions and try again (l 6).
≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/
iPhone/iPad and turn it on before connecting.
≥ The USB device is not inserted. Check the connection.
"NO DISC"
≥ Insert the disc to be played (l 6).