Initial Configuration - EHEIM climacontrol+ Serie Manual De Instrucciones

página de 128

/ 128
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

English

1. Guide the hose (Ø 16/22) through the hose clamp⑫ and the

hose lock⑬.

2. Slide the union nut ⑭ onto the hose connecting piece⑯.

3. Insert the seal ⑮ into the union nut.

4. Connect the hose to the hose connecting piece.

For a hose of Ø 19/27, first pull the reducing coupling ⑰ onto the

hose connecting piece. Then connect the hose.

5. Secure the hose connection to the hose lock. Use pliers for

this.

6. Connect the pressure side of the filter and/or pump (return flow

into the aquarium) with the connection IN of the climate control

unit. Connect the return flow of the water to the aquarium to

the connection OUT at the climate control unit.

7. Tighten the union nuts of the two hose connecting pieces

hand-tight. Do not use pliers!

Maintenance

DANGER! Electric shock!

▶ Prior to any maintenance, pull the switching power supply unit

of the WiFi controller and the mains plug of the climate control

unit.

CAUTION! Material damage.

▶ Do not use hard objects or aggressive cleaning agents for

cleaning.

▶ All components are not dishwasher-resistant.

The following sections describe maintenance work necessary for

optimum and fault-free operation. Regular maintenance prolongs

the service life and assures functionality of the climate control

unit over a long period.

Cleaning the air filter

Recommended maintenance

Clean the air filter ⑲ approx. every 2 – 3 weeks but at least once

a month.

1. Fold the plastic grilles ⑳ at the front side of the climate control

unit forward.

2. Remove the air filter and clean it with lukewarm water.

3. Reinsert the dry air filter at the front side and close the plastic

grille.

Prior to disconnecting the hose lines from the climate control unit,

stop the water circuit by turning off the pump and/or filter. Press

the hose clamps ⑫ together to prevent water from leaking out.

Commissioning

CAUTION! Material damage.

▶ Do not operate the climate control unit without a water flow.

▶ Ensure that the water circuit has been established and the

piping has been ventilated completely.

1. Start the pump and/or filter in order to start the water circuit.

2. Wait approx. 2 minutes to ensure the piping has been ventilat-

ed completely.

3. Check to ensure that the hose connections ⑥/⑦ of the climate

control unit are watertight (⌦F).

4. Insert the switching power supply unit ④ of the WiFi controller

into the mains socket.

5. Insert the mains plug ⑧ of the climate control unit into the

mains socket. The display at the front says OFF (⌦L).

Operation with WLAN connection

CAUTION! Material damage.

▶ Do not connect any devices other than the WiFi controller

included in the scope of delivery.

System requirement

WLAN-enabled terminal device (smartphone, tablet, notebook etc.)

Creating the network

1. Insert the switching power supply unit in the mains socket. The

status LED ⑱ illuminates.

‧ The status LED flashes white: The network is being searched

for or created

‧ The status LED illuminates blue: A new network has been

established.

‧ The display of the device shows the current water temperature.

‧ When it is first started, the compressor starts with a delay of 2

minutes.

Connecting to the WLAN network

2. Open the network settings of your terminal device (smart-

phone, tablet, notebook etc.).

3. Connect the terminal device to the WLAN network (SSID)

EHEIM clima XXXXXXXX.

4. Enter the network security key.

You can find the security key of the network on the label at the

back of the WiFi controller. Alternatively, you can also scan the

QR code 1 (see label) to establish the connection.

Calling up the website

5. Open your web browser and enter the following address:

http://192.168.1.1, eheimdigital oder eheimdigital.local

Alternatively, you can also scan the QR code 2 (see label) to

open the software in the browser.