Milwaukee M18 FUEL Manual Del Operador página 6

To reduce the risk of personal in-
WARNING
jury and damage to the tool or work:
•Always use the "hammering-only" setting to
set the anchor. Never use the "hammering-with-
rotation" setting to set the anchor.
•Never switch the tool to "hammering-with-
rotation" until after the anchor has been set
and the tooth anchor chuck has been removed
from the anchor.
Setting Self-Drilling Anchors
MILWAUKEE Tooth Anchor Chucks require a "B"
taper adapter.
1. Place the proper size tooth anchor chuck into the
"B" taper adapter. Then insert the "B" taper adapter
into the tool and lock it into place as described.
See "Installing Bits and Chisels".
2. Insert the anchor into
t h e t o o t h a n c h o r
chuck. Set the knob
for hammering only.
Set the anchor on
your mark and ham-
mer until the teeth
have penetrated the
concrete.
3. Set the knob for ham-
mering with rotation
and drill until the
chuck is 1/8" above
the concrete.
NOTE: It may be nec-
essary to clean dust
and cuttings from the
anchor several times
while drilling the hole.
4. Remove the anchor
from the hole while the
tool is running. Clean
the dust and cuttings
from the anchor by
pointing it downward
and turning the tool on
and off several times.
Clean the dust out of the hole with a vacuum
cleaner or blowout bulb.
5. Place the expansion
plug into the anchor
and insert the anchor
into the hole. Switch
the knob back to ham-
mering only, and ham-
mer the anchor firmly
into the hole.
6. Snap the head off of
theanchor. To remove
the head of anchors up
to 5/8", grasp the han-
dles firmly and pull the
tool sharply towards
you or snap off the an-
chor head with a hand
hammer as shown. The
anchor is now ready to receive a bolt.
7. To remove the anchor head wedged in the tooth
anchor chuck, use drift pin 48-86-0100.
8. To remove the tooth anchor chuck, remove the
MILWAUKEE Rotary Hammers may be used for
chipping and chiseling.
When chiseling, hold the tool at an angle to the
workpiece. Work from a corner or close to the edge
of the workpiece, breaking off one small area at a
time rather than attempting too large an area.
A variety of accessories are available.
1/8"
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
6
"B" taper adapter from the nose of the tool. Insert
the drift pin supplied with the adapter into the hole
on the side of the "B" taper adapter and strike it
sharply to force out the tooth anchor chuck.
Chiseling and Chipping
Bushing Tools
Used to surface concrete.
Mortar Cutting Chisels
(Seam Tools)
For removing old mortar for tuck
pointing or caulking.
Bull Points
For demolition work and starting
holes in concrete slabs.
Flat Chisels
For edging, chipping or
channeling.
Scaling Chisels
For removing weld spatter or
scale and cutting straight lines.
Slotting Chisel
For slotting and cutting between
drilled holes in concrete and
masonry.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
Maintaining Tool