stayer HL105B Manual De Instrucciones página 17

The device has been designed to clean surfaces and
objects in the elements, tools, vehicles and boats. With
special accessories can be mixed for the cleaning
products recommended by STAYER, unclogging pipes
and loosen rust or paint.
This product is not suitable for industrial use. Regulatory
use also involves the use at an ambient temperature
between 5 ° C and 50 ° C.
This manual includes instructions on
proper installation and safe use of
machinery. It is very important to read
carefully these instructions.
1. List of contents
2. Special safety instructions...................................12
3. Machine-specific Safety Warnings.......................13
3.1. Placing or fixing the tool........................................13
3.2. Assembling..........................................................13
3.3. Electrical connection............................................13
3.4. Illustrated description...........................................13
4. Operating instructions..........................................13
4.1. Placement and testing..........................................13
4.2. Instructions for use...............................................14
5. Maintenance instructions.....................................14
5.1. Cleaning, maintaining, lubricating, sharpening.....14
5.2. Repair service......................................................15
5.3. Guarantee............................................................15
6. Legal Regulations.................................................15
6.1. Technical features................................................15
6.2. EC Declaration of Conformity...............................15
2. Machine-specific Safety Warnings
Before start-up please read these instructions!
Before using the machine please read the
!
operating instructions for your unit and
comply in particular with these safety
instructions. Please keep the instructions
safe for later use.
The warning and information signs
attached to the unit provide important
information for safe operation.
Apart from the information in the operating
instructions comply with the general safety
regulations and regulations for the prevention of
accidents.
Machine not suitable for connection to the
potable water mains.
Never direct the water jet at
people, animals, the unit or
electric components.
!
High pressure jets can be dangerous if
subject to misuse.
ENGLISH
12
Power suply
The voltage indicated on the rating plate must correspond
to the voltage of the power source.
Class 1 units may only be connected to properly earthed
power sources.
This equipment is only connected into a socket which is
protected by a circuit-breaker that would be actuated by a
30 mA residual current. If an extension cord is used, the
plug and socket must be of a water tight construction.
Warning. Inadequate extension cords can be
dangerous. Never touch the mains plug with wet
hands.
Page
Do not run over, crush or pull the power supply cable or
extension lead, otherwise it may be damaged. Protect the
cable from heat, oil and sharp edges.
The extension lead must have a cross section in
accordance with the operating instructions and be
protected against splashed water. The connection must
not be in water.
Water connection
Comply with the regulations of your water supply
company.
All connecting hoses must have properly sealed joints.
The high-pressure hose must not be damaged (danger of
bursting). A damaged high-pressure hose must be
replaced immediately. Only use hoses and connections
recommended by the manufacturer.
Application
Before use, check that the unit and operating equipment
are in perfect condition and are safe to operate. Do not use
the unit if it is not in perfect condition.
Never draw in solvent-containing liquids, undiluted acids
or solvents! This includes petrol, paint thinners heating oil.
The sprayed vapour is highly flammable, explosive and
toxic; also acetone, undiluted acids and solvents as these
corrode the materials used on the unit.
The appropriate safety regulations must be observed
when using the unit in dangerous area (e.g. petrol
stations). It is forbidden to operate the unit in
potentially explosive locations.
The gun trigger must not be jammed in the "ON" position
during operation.
Suitable protective clothing must be worn if necessary to
protect against splashing from some parts.
Vehicle tyres/tyre valves may only be cleaned from a
minimum distance of 30 cm, otherwise the vehicle
tyre/tyre valve could be damaged by the high-pressure jet.
The first indication of this is a discoloration of the tyre.
Damaged vehicle tyres/tyre valves can be deadly
dangerous.
Materials containing asbestos and other materials which
contain substances which are hazardous to your health
must not be sprayed.
Only use detergents which have been approved by the
manufacturer of the unit.
12