Kinderkraft GRANDE Manual De Usuario página 21

Ocultar thumbs Ver también para GRANDE:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 23
• Check that the pram body or seat unit or car seat
attachment devices are correctly engaged before use.
• This product is not suitable for running or skating.
Age and weight usage: from 0 months up to 15 kg.
We recommend using lowest reclined position for newborn babies.
This product may only be used by one child at the same time
The parking device shall be engaged when placing and removing the children
The maximum basket load is 2 kg. Any additional load suspended from the buggy handles, backrest and sides will cause
stability loss.
Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.
Lift the front suspension when going up a curb or step.
Do not place the product near open flame or other heat sources.
Do not use with an additional platform.
B. ASSEMBLY
I. Buggy components (FIG. 1)
A.
Seat frame and safety straps
B.
Front wheels
C.
Rear wheels
D.
Safety bar
II. UNFOLDING BUGGY FRAME
Place the frame on a flat surface with its handle up (FIG. 2). In order to unfold the frame, move the lock (FIG. 2A) on the
right side of the buggy and lift the frame until you hear the locking sound (FIG. 2B). A properly unfolded frame is shown
in FIG. 3.
III. WHEEL ASSEMBLY/DISASSEMBLY
Insert the rear wheels into the slot in the rear axle until they are entirely blocked (FIG. 4). In order to remove the rear
wheels, unlock the locking button located on both sides of the rear axle (FIG. 5A) while pulling the wheels out of the slots
(FIG. 5B). Insert the front wheels in the slot in the front axle until you hear the locking sound (FIG. 6). To remove the front
wheels, push the quick release button located below the footrest under each wheel (FIG. 7). The buggy has a system of
swivel front wheels with a possibility of locking for straight movement. To lock the wheel to move forward, slide the ring
located above the wheel (FIG 8).
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. CANOPY INSTALLATION
When installing the canopy, slide the attachments into the guides on both sides of the frame until they lock (FIG. 9). Then
fasten the Velcro fasteners on both sides of the canopy (FIG. 10). A correctly mounted canopy is shown in FIG. 11. In order
to unfold another layer of the canopy, unfasten the zip on the canopy (FIG. 12).
V. ASSEMBLY/DISASSEMBLY OF THE SAFETY BAR AND LEG COVER
The safety bar must be inserted in appropriate holes on both sides of the frame, as shown in FIG. 13. To remove the bar,
press the buttons on both sides and remove the bar (FIG. 14). Leg cover has four Velcro fasteners located on the inner
side (FIG. 15). In order to attach the cover, fasten the Velcro fasteners on the seat frame tubes.
VI. USE OF BRAKE
The buggy is equipped with a foot brake located on the rear axle. Press the lower part of the brake down; the brake is
activated when you hear the locking sound (FIG. 16). The brake is unlocked by pressing the upper part of the brake.
VII. BACKREST AND FOOTREST ADJUSTMENT
The seat is equipped with smooth backrest adjustment system, from a lying to a sitting position, using a clasp (FIG. 17A).
The footrest has 4 positions. Press the buttons on both sides (FIG. 17B) to change the footrest position.
VIII. SAFETY STRAPS
The buggy's straps are adapted in such a way to enable its use even by new-borns. Always use the fastening system.
To secure the child, connect the latches of the hip and shoulder straps and then insert them into the middle clasp until it
engages (FIG. 18A). Adjust the straps each time. Removing the straps (for cleaning): Take the shoulder and hip straps out
of the openings (FIG. 18B).
IX. SEAT COVER REMOVAL
Remove the canopy, safety straps and safety bar. To remove the seat cover, unfasten the press studs located on the
buggy frame (FIG. 19A) and take the cover off the hooks located next to it (FIG. 19B). Then unfasten the middle Velcro
fastener located under the seat (FIG. 20A) and the strap under the footrest (FIG. 20B), and remove the cover. Install the
seat following the steps described above in reverse order.
E.
Visor
F.
Leg cover
G.
Rain cover
21

Publicidad

Tabla de contenido
loading

Tabla de contenido