Self-Diagnosis Function; Specifications - Sun Microsystems GDM-5510 Manual De Instrucciones

Self-diagnosis function

This monitor is equipped with a self-diagnosis function. If there is
a problem with your monitor or computer(s), the screen will go
blank and the ! (power) indicator will either light up green or
flash amber. If the ! (power) indicator is lit in amber, the
computer is in power saving mode. Try pressing any key on the
keyboard or moving the mouse.
INPUT
1 2
! (power) indicator
x If the ! (power) indicator is green
1
Disconnect any plugs from the video input 1 and 2
connectors, or turn off the connected computer(s).
2
Press the ! (power) button twice to turn the monitor
off and then on.
3
Hold the control button upward for 2 seconds
before the monitor enters power saving mode.
OK
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cables and check
the condition of your computer(s).
If the color bars do not appear, there is a potential monitor failure.
Inform your service representative of the monitor's condition.
x If the ! (power) indicator is flashing amber
Press the ! (power) button twice to turn the monitor off
and then on.
If the ! (power) indicator lights up green, the monitor is working
properly.
If the ! (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between amber
flashes of the ! (power) indicator and inform your service
representative of the monitor's condition. Be sure to note the
model name and serial number of your monitor. Also note the
make and model of your computer and graphic board.
MENU
OK

Specifications

CRT
Viewable image size
Resolution
Maximum
Recommended
Input signal levels
Standard image area
Deflection frequency*
AC input voltage/current 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A
Power consumption
Operating temperature
Dimensions
Mass
Plug and Play
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8% of
total horizontal time or 0.8 µs, whichever is larger.
• Horizontal blanking width should be more than 2.3 µsec.
• Vertical blanking width should be more than 450 µsec.
** If the input signal is Generalized Timing Formula (GTF)
compliant, the GTF feature of the monitor will automatically
provide an optimal image for the screen.
Design and specifications are subject to change without notice.
19
0.24 mm aperture grille pitch
21 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 403.8 × 302.2 mm (w/h)
(16 × 12 inches)
19.8" viewing image
Horizontal: 2048 dots
Vertical: 1536 lines
Horizontal: 1600 dots
Vertical: 1200 lines
Video signal
Analog RGB: 0.700 Vp-p
(positive), 75 Ω
SYNC signal
H/V separate or composite sync:
TTL 2.2 kΩ, Polarity free
Sync on Green: 0.3 Vp-p
(negative)
Approx. 388 × 291 mm (w/h)
3 × 11 1
(15 / / inches)
8 2
or
Approx. 364 × 291 mm (w/h)
3 × 11 1
(14 / / inches)
8 2
Horizontal: 30 to 130 kHz
Vertical: 48 to 170 Hz
Approx. 135 W
10 °C to 40 °C
Approx. 501 × 508 × 505 mm (w/h/
3 × 20 × 20 inches)
d) (19 /
4
Approx. 31.5 kg (69 lb 7 oz)
DDC2B/DDC2Bi, GTF**
EN