Publicidad
Idiomas disponibles
Idiomas disponibles
H-9345, H-9346
H-9347
POWER PLUS DRUM FAN
TOOLS NEEDED
T25 Torx
Phillips Head
Screwdriver
• Unit includes 110-120 Volt A/C polarized-grounded
plug with 15' supply cord.
• To reduce risk of fire or electric shock, do not use
with any solid state speed control device. Drum
fan is equipped with an automatic reset overload
device. Unit may start unexpectedly.
• Do not put any object through the grilles into the
blade or motor.
Always unplug or disconnect the fan from the
power supply before servicing.
Do not remove front and rear grills at the
same time. Doing so may result in difficulty
reinstalling them.
The following steps describe grill removal process in
order to access fan part for maintenance.
1.
With fan turned off and
unplugged, coil the
cord and locate close
to user.
2. Using T25 Torx
screwdriver, loosen, then
remove all of the grill
fasteners on front and
rear grills. (See Figure 1)
PAGE 1 OF 6
1-800-295-5510
uline.com
11/32" Wrench
Screwdriver
SPECIFICATIONS
MAINTENANCE
Figure 1
Pliers
• Do not remove grounding conductor from plug or
use with an extension cord.
WARNING
• Unit is designed for indoor use only. Do not expose
to the elements or allow to become wet.
• Do not use to exhaust hazardous chemicals or
vapors.
• Unplug unit for storage when not in use or when
moving locations.
NOTE: For front grills, skip to Step 8.
3. For rear grills, remove ground wires with a 11/32"
wrench and Phillips head screwdriver.
(See Figures 2a and 2b)
NOTE: Grill will need to be partially removed to
complete steps 3-7. (See Figure 2c)
Figure 2a
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Figure 2b
Figure 2c
0221 IH-9345
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-1196
Resumen de contenidos para Uline H-1196
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-9345, H-9346 1-800-295-5510 H-9347 uline.com POWER PLUS DRUM FAN TOOLS NEEDED T25 Torx Phillips Head 11/32" Wrench Pliers Screwdriver Screwdriver SPECIFICATIONS • Unit includes 110-120 Volt A/C polarized-grounded •...
- Página 2 (See Figure 3) Figure 5 Figure 3 Carefully remove grills. (See Figure 6) 5. Disconnect white wires. (See Figure 4) Figure 6 Figure 4 8. To install grill, reverse the above steps. 1-800-295-5510 PAGE 2 OF 6 0221 IH-9345 uline.com...
-
Página 3: Ventiladores Tipo Tambor De Alta Potencia
H-9345, H-9346 800-295-5510 H-9347 uline.mx VENTILADORES TIPO TAMBOR DE ALTA POTENCIA HERRAMIENTAS NECESARIAS Desarmador Desarmador Llave de 11/32" Pinzas Torx T25 de Cruz ESPECIFICACIONES • La unidad incluye clavija de 110-120 Voltios de • No quite de la clavija el conductor de aterrizado ni Corriente Alterna con polos aterrizados y cable utilice una extensión. -
Página 4: Continuación De Mantenimiento
Diagrama 3 Retire las rejillas con cuidado. (Vea Diagrama 6) 5. Desconecte los cables blancos. (Vea Diagrama 4) Diagrama 6 Diagrama 4 8. Siga los pasos a la inversa para reinstalar la parrilla. 800-295-5510 PAGE 4 OF 6 0221 IH-9345 uline.mx... -
Página 5: Outils Requis
H-9345, H-9346 1-800-295-5510 H-9347 uline.ca VENTILATEUR DE TYPE BARIL GRANDE PUISSANCE OUTILS REQUIS Tournevis Torx T25 Tournevis cruciforme Clé de 11/32 po Pinces CARACTÉRISTIQUES • L'appareil comprend une fiche polarisée de 110 à • Ne retirez pas le conducteur de terre de la fiche et 120 VCA reliée à... - Página 6 Figure 3 Retirez délicatement les grilles. (Voir Figure 6) 5. Déconnectez les fils blancs. (Voir Figure 4) Figure 6 Figure 4 8. Pour installer les grilles, suivez les étapes ci-dessus en sens inverse. 1-800-295-5510 PAGE 6 OF 6 0221 IH-9345 uline.ca...