Optional Accessory - DeWalt DCH832 Manual De Instrucciones

nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 9 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the bail/
loop style auxiliary handle
main handle 5 .
SHOCKS Active Vibration Control®
System
For best vibration control, hold the tool as described in
Proper Hand Position and apply just enough pressure so the
damping device on the main handle is approximately mid
stroke. The hammer only needs enough pressure to engage
the active vibration control. Applying too much pressure will
not make the tool actuate faster and active vibration control
will not engage.
D WALT Bluetooth® Tool Tag Ready (Fig. A)
e

Optional Accessory


WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.

WARNING: Remove battery from tool before installing
the D WALT Bluetooth® Tool Tag.
e

WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be
sure to securely tighten the screws.
Your tool comes with mounting holes
for installing a D WALT Bluetooth® Tool Tag (DCE041). You will
e
need a T15 torx bit tip to install the tag. Screw torque should
be between 0.8 and 1.2 Nm (7.1 to 10.6 in-lbs). The D
Tool Tag is designed for tracking and locating professional
power tools, equipment, and machines using the D
Tool Connect™ app. For proper installation of the D
Tool Tag, refer to the D WALT Tool Tag manual. To learn
e
more, visit:
www.D WALT.com/en-us/jobsite-solutions/tool-connect
e
Electronic Speed and Impact Control
(Fig. A)
The electronic speed and impact control allows the use of
smaller chisels without the risk of chisel breakage, chipping
into light and brittle materials without shattering and
optimal tool control for precise chiseling.
8 into the tool handle, align the
2 with the other hand on the
11 and fasteners
To set the speed dial
The higher the number, the greater the speed and impact
energy. Dial settings make the tool extremely flexible and
adaptable for many different appli cations. The required
setting depends on the chisel size and hardness of material
being chipped.
Wireless Tool Control™ (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the hammer.
Your hammer is equipped with a Wireless Tool Control™
transmitter which allows your hammer to be wirelessly
paired with another Wireless Tool Control™ device, such as a
dust extractor.
To pair your hammer using Wireless Tool Control™, press and
hold the trigger switch
Tool Control™ pairing button on the seperate device. An LED
on the seperate device will let you know when your hammer
has been successfully paired.
Mode Selection (Fig. A)

WARNING: Do not select the operating mode when
the tool is running. Tool must come to a complete stop
before activating the mode selector button or damage
to the tool may result.
Your tool is equipped with a mode selector dial
select the mode appropriate to desired operation.
symbol
WALT
e
To Select a Mode
• Rotate the mode selector dial
WALT to the symbol corresponding for the desired mode.
e
nOTE: The arrow on the mode selector dial
pointing at a mode symbol at all times. There are no operable
12 positions in between.
Indexing the Chisel Position (Fig. A)
The chisel can be indexed and locked into
WALT
e
24 different positions.
1. Rotate the mode selector dial
WALT
e
the
WALT
e
2. Rotate the chisel in the desired position.
3. Set the mode selector dial
4. Twist the chisel until it locks in position.
10 , turn the dial to the desired level.
on the hammer and the Wireless
1
Mode
Chisel Chisel position
Adjustment adjustment
Light chipping, chiseling
Chipping
and demolition
4
4
position.
to the "Chipping" position.
4
English
4 to
Application
so that the arrow points
4 must be
until it points towards
9